background image

 

 

 

- 1 - 

 

  Precautions 

Please  read  the  user  manual  before  installation  and  operation  of  the 

device. Please keep the User Manual for future reference. 

1.1

 

Installation Precautions 
 

 

The device should only be installed by qualified personnel. 

 

Please check the voltage rating before connecting the power. It is 
recommended not to share the same power socket with other high 
power-rated devices (examples: Hairdryer, Refrigerator, Iron). 

 

Do not place the device in the vicinity of flammable or conductive 
materials, high temperature (direct sunlight), moisture, or other 
appliances that produce heat. 

 

Always make sure the device is properly ventilated, do not place 
any objects on the device to avoid overheating. 

 

Ensure the device is installed on an even surface. 

 

The power socket and power cable shall be inspected regularly 
and replaced in case ofdamage to avoid risk of electric shock or 
fire. 

1.2

 

Operation Precautions  
 

 

Do not attempt to repair the device in any occasion. Improper 
disassembly of the device may expose you to electric components 
and may cause shock or other risks. Please contact your service 
provider if there are problems with the device. 

 

 

Unplug the power before cleaning equipment. Use a soft and dry 
cloth to clean the equipment.Avoid the use of liquid or aerosol. 

 

Prevent liquid spillage on the device to avoid short circuit.  

 

Ensure a proper environment for the device to avoid overheating; 
do not block the device ventilation outlet. 

 

Please contact the Service Provider if you are in doubt in on how 
to connectother electronic devices to the ONT to avoid possible 
damage to the devices. 

 

 

Summary of Contents for G-140W-C











Reviews: