background image

 

- 8 -

 

4

 

Hazardous Substances 

 

 
 

Parts 

Hazardous Substance

 

Pb 

Hg 

Cd 

Cr

6+

 

PBB 

PBDE 

Circuit Modules 

× 

 

× 

 

 

 

Cables & Cable 
Assemblies

 

× 

 

 

 

 

 

Metal Parts 

× 

 

 

 

 

 

Plastic and 
Polymeric parts 

 

 

 

 

 

 

Indicates that the concentration of the hazardous substance in all homogeneous 
materials  in  the  parts  is  below  the  relevant  threshold  of  the  SJ/T11363-2006 
standard. 

×: Indicates that the concentration of the hazardous substance of at least one of all 

homogeneous  materials  in  the  parts  is  above  the  relevant  threshold  of  the 
SJ/T11363-2006 standard. 

 
This  table  shows  where  these  substances  may  be  found  in  the  supply  chain  of 

NokiaElectronic information products, as of the date of sale of the enclosed product. 
Note  that  some  of  the  component  types  listed  above  may  or  not  be  a  part  of 
theenclosed product.

 

 
 
 
 
 
 
 

 

 

 
The Environment-Friendly Use Period (EFUP) for all enclosed products and  
their parts are per the symbol shown here, unless otherwise marked. Certain  
parts may have a different EFUP (for example, battery modules) and so are  
marked to reflect such. The Environment-Friendly Use Period is valid only  
when the product is operated under the conditions defined in the product manual. 

Summary of Contents for G-140W-C











Reviews: