background image

M1122 Administrator Manual

 

E

 Copyright Nokia Networks Oy

C33906001SE_00

 5-42

Command

Save configuration to file

Description

Saves the configuration to a file.

Syntax

save config {file<filename> | startup | user}

Arguments

filename

 is the name of the file in which you want to

save the configuration.

startup-config

 argument saves the configuration

into a startup.cfg file.

user

 saves the user configuration.

Example

M1122>save config startup-config
M1122>

Command

Restore configuration

Description

Restores the default or user configuration. You must
have the admin privileges to issue this command. Re-
start your M1122 after you have issued this command.

Syntax

restore config {default | user}

Arguments

default

 argument restores the default configuration of

M1122.

user

 argument restores the user configuration. The

user configuration can be made with admin rights only.

Example

M1122>restore config default
M1122>

Command

Clear counters

Description

Clears the statistics counters.

Syntax

clear {log | eth | atm | bridge | ppp | ip}

Arguments

log

 argument rewinds the diagnostic log to the begin-

ning of the log file.

eth

 argument clears the Ethernet statistics counters.

atm

  argument clears the ATM statistics counters.

bridge

 argument clears the bridging counters.

ppp

 argument clears the PPP counters.

ip

 argument clears the IP statistics counters.

Example

M1122> clear log
M1122>

Summary of Contents for M1122












































































































Reviews: