Caution
If any lights do not work on your pre-lighted tree, please check the following:
TROUBLESHOOTING:
1. If entire tree or a section of the tree does not light:
T
roubleshoo
ting
a) Make sure each section of the tree is well connected.
b) Check that there is power at the electrical outlet.
c) Check fuse in the plug of the power supply cord and replace if necessary (see
below).
Fuse Replacement
2. If a strand of lights still does not work:
a) Check that all bulbs are tightly fitted inside the sockets and that no bulbs are broken or missing. Replace
any broken or missing bulbs with replacement bulbs provided (see Bulb Replacement below). If all bulbs
are firmly in the sockets, slightly twist the bulbs from side to side to ensure proper connection.
b) If the lights still do not work, carefully remove each bulb one by one from the problem light string. Pull
the bulb AND plastic base straight out of the socket. Do not twist bulbs while removing from sockets.
Check the two wires at the bottom of the bulb holder. Each wire should be aligned properly on the bulb
holder to ensure a proper connection in the lamp socket. If one wire is missing or too short, please
replace bulb with a replacement bulb (provided).
5. Insert the end connector of power cord into the plug fixed on the bottom section ( C) and
always match the
3. Insert the middle section (B) of the tree into the bottom section ( C). (see Fig. 2)
4. Insert the top section ( A) into the middle section (B). (see Fig. 3)
6. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure that
all wires are free of branch hinges (see Fig. 5).
7. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one along
the centre of the main stem. Repeat pattern for each branch (see Fig. 6).
8. Plug the well-connected power supply cord from the bottom section ( C) into electrical outlet. This tree is
CAUTION! - ALWAYS UNPLUG YOUR TREE FROM
ITS POWER SOURCE BEFORE ATTEMPTING BULB
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products basic precautions should always be followed including the following:
,
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles, or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let bulbs rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electrical product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not
be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
l) This product has overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse
m) Do not cover the product with cloth, paper, or any material not part of the product when in use.
blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the
product. Replace the fuse as per the User Servicing Instructions (follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded.
n) This product is equipped with push-in type bulbs. Do not twist bulbs.
o) Read and follow all instructions that are on the product or provided with the product.
Color Changing, just press the foot pedal switch to change functions. The 8 lighting options available are, Steady
Warm White, Flashing Warm White, Slow Fade Warm White, Steady Multicolor, Flashing Multicolor, Slow Fade
Multicolor, Sequential Multicolor & Warm White, Slow Fade Multicolor & Warm White.
AND FUSE REPLACEMENT.
protuberance on the end connector of power cord to the
on the
fixed on the bottom section (C)
concave
plug
according to the magnified drawing
according to the magnified drawing on Fig.4.
p) SAVE THESE INSTRUCTIONS.
