background image

- 6 - 

OPERATION 

Adjust the thermostat control (not included) to increase/decrease the 

temperature setting. 

MAINTENANCE 

WARNING: 

To reduce the risk of fire or electric shock, always 

switch off the unit and wait 10 minutes to allow it to cool before attempting 

any maintenance or cleaning. It is recommended that the heater is cleaned 

periodically, in order to avoid dust blocking the grill or ventilation. 

CLEANING 

1. Wipe the unit with a soft, damp cloth. 

2. Do not use abrasive cleaners or spray liquids on the unit surfaces. 

3. Remove the filter from the back of insert and remove the dust. Make sure to reinstall 

it on the unit in order to protect the heating element against the dust and dirt. 

WARRANTY

 

LIMITED 1-YEAR WARRANTY 

This Noma® product carries a 

one-(1) year

 warranty against defects in workmanship 

and materials. Trileaf Distribution agrees to replace a defective product, within the 

stated warranty period, when returned to the place of purchase with 

proof of purchase

This product is not guaranteed against wear or breakage due to misuse and/or abuse. 

 

Noma® is a registered trademark of Noma Company and is used under licence. 

Imported by Trileaf Distribution Toronto, Canada M4S 2B8 

 

Made in China 

 

Summary of Contents for 52-2510-0













Reviews: