Norac UC5 MAX Installation Manual Download | Manualshive

Page: 8 / 16

background image

5

3.2.2

Installation with 3-Way Coupler and Terminator Plug

1.

Remove the terminator plug (E20) from the existing 3-way coupler installed at the outer
sensor.

2.

Install the 3-way coupler (E10) at the inner sensor. Plug the terminator plug (E20) and the
sensor cable into the 3-way coupler.

3.

Connect the CANbus cable (C06) between the 3-way couplers.

Components shown in black are included in this kit.

Components shown in green are included in the bracket and hardware kit.

Components shown in blue are existing components.

Figure 7: Electrical Installation: 3-Way Coupler and Terminator Plug

«
...
6
7
8
9
10
...
»

Summary of Contents for UC5 MAX

















Reviews:

No comments

Related manuals for UC5 MAX

Brand: Ubisys Pages: 2

Brand: Hamworthy Pages: 10

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Harmony Controller 2000

Brand: A10 Pages: 27

Brand: Dahua Pages: 58

Brand: Dakota Digital Pages: 6

CMD-2000 Series

Brand: Dakota Digital Pages: 10

Brand: Z-Wave Pages: 6

Brand: Feig Electronic Pages: 153

Brand: LaserBit Pages: 69

Brand: Lawler Pages: 5

Tissue-Tek TEC 6

Brand: Sakura Seiki Pages: 6

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

ConferenceSHOT AV

Brand: VADDIO Pages: 114

Brand: Vacon Pages: 40

Brand: JASTEC Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands