Norac UC5 MAX Installation Manual Download | Manualshive

Page: 9 / 16

background image

6

4

Roll Sensor Removal

1.

Locate the two NORAC roll sensors (small rectangular box with a cable running from it).
There will be one mounted on the boom frame and one mounted on the intermediate
frame of the sprayer. Some machines will have a third roll sensor mounted on the chassis.

2.

Disconnect and remove all roll sensors. Refer to the installation manual for the specific
make/model of sprayer for roll sensor mounting locations. Installation manuals are available
at

www.norac.ca

.

3.

Insert the 6-pin plugs (P03) into the 8-way coupler where the roll sensors were connected.

Figure 8: NORAC Roll Sensor

Figure 9: NORAC 8-Way Coupler

«
...
7
8
9
10
11
...
»

Summary of Contents for UC5 MAX

















Reviews:

No comments

Related manuals for UC5 MAX

Brand: Tapeswitch Pages: 13

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brand: Quectel Pages: 73

Brand: Vaillant Pages: 11

Brand: WAREMA Pages: 4

Brand: CAME Pages: 2

Brand: Osram Pages: 3

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Brand: Tenpilot Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands