22 | Nord PiaNo 5 User MaNUal os v1.1x
9
MeNUs
settings that are made in the
System
,
Sound
,
MIDI
and
Pedal
menus
have immediate effect and are stored until they are changed again,
except for the
Local Control
Midi setting. This setting always reverts to
“on” when the Nord Piano 5 is powered up.
enter a menu by holding
SHIFT
and pressing
SYSTEM
,
SOUND
,
MIDI
or
PEDAL
(Program select buttons 1, 2, 3 and 4). Menus are navigated with
the on-screen
3
and
4
soft buttons and settings are changed with the
PROGRAM
dial. soft buttons are also used to access additional settings,
where applicable.
exit a menu by pressing
EXIT
(shift).
sYsTeM MeNU
1 - MeMorY ProTeCT
The memory protection setting is
On
when a Nord Piano 5 leaves the
factory, preventing accidental overwriting of programs. setting this to
Off
enables store operations. Menu settings and live programs are not
affected by this setting.
Range: On (default), Off
2 - GloBal TraNsPose
This setting allows for transposing the entire Nord Piano 5 in semitone
steps. This setting will be
added
to any on-panel transpose value stored
with a program.
Range: +/- 6 semitones (default value is “none”)
3 - FiNe TUNe
Fine Tune can be used to fine tune the pitch of the Nord Piano 5 in finer
increments.
Range: +/- 50 Cents (+/- half a semitone). Default value is “0”
4 - versioN aNd Model iNFo
The version and model info menu page shows the full version number
of the currently installed os (operating system) and, when turning the
Program dial, hardware information for the instrument.
Use the Program dial to switch between Version and Model info
soUNd MeNU
1 - PiaNo Pedal Noise level
sets the level of the dynamic Pedal Noise feature which can be turned
on for pianos that support it, if a Nord Triple Pedal is connected to the
Nord Piano 5.
Range: +/- 6 dB (0 dB default
2 - PiaNo sTriNG res level
sets the level of the string resonance feature that can be turned on for
selected pianos (acoustic Med, lrg and xl sizes).
Range: +/- 6 dB (0 dB default)
Midi MeNU
1 - loCal CoNTrol
Midi local Control determines if the Nord Piano 5 keyboard and panel
will control internal sound engines and programs or only transmit Midi.
local Control
On
is the normal “play mode”. When local Control is in
Off
mode, front panel and keyboard actions are transmitted via Midi only.
Range: On (Default), Off
M
Local always defaults back to “On” every time the Nord Piano 5 is
powered on
2 - Midi CHaNNel
This sets the transmitting and receiving Midi channel for the Nord Piano
5. This Midi channel transmits all keyboard, pedal and panel actions as
Midi signals. it can also be used as a receiving channel with full control
of the entire Piano 5.
Range: 1-16, Off (Default 1)
3 - CoNTrol/ProGraM CHaNGe Mode
CC (CoNTrol CHaNGe)
This allows you to set if you want your Nord Piano 5 to transmit and/or
receive Midi Controller Messages or not on the Midi channel.
Range: Off, Send, Receive, Send & Receive (Default)
PC (ProGraM CHaNGe)
This setting determines whether your Nord Piano 5 transmits and/or
receives Midi program Change Messages, on the Midi channel.
Range: Off, Send, Receive, Send & Receive (Default)
4 - TraNsPose Midi aT
When set to
In
, active transpose values (global and/or set per program
using the on-panel Transpose control) are
not
applied to outgoing
Midi, but only to incoming Midi data. in
Out
mode sent Midi notes are
transposed but not incoming ones.
Range: In (Default), Out
5 - Midi oUT veloCiTY CUrve
There are three options for how the velocity of outgoing Midi notes
is scaled. When set to
Heavy
, the generated Midi corresponds to
