2 Mounting and installation
BU 0200 en-US-4920
59
Pos : 121 /Anleit ungen/El ektr onik /FU und St art er/2. M ontage und I nst allation/ Elek trischer Ans chl uss/ Elek trischer Ans chl uss _01 (Ü bers chrift) [SK 1xx E, SK 2xxE, SK 5xx E, SK xx xE-FD S, SK 500P, SK300P] @ 12\m od_1467020207250_14638. docx @ 333211 @ 2 @ 1
2.4 Electrical connection
Pos : 122 /Anleit ungen/El ektr onik /FU und St art er/1. Allgemei nes /Sic herheits- und Ins tall ations hinw eis e und W arn- Gefahrenhinw eise/neu/War n- und Gefahrenhinw eise/WARNUN G - Elek trischer Schl ag (Spannung, auch wenn G erät auß er Betri eb) [dez entral außer FDS] @ 41\m od_1585136481755_14638. docx @ 2599401 @ @ 1
WARNING
Electric shock
Dangerous voltages can be present at the power input and the motor connection terminals even when
the device is not in operation.
• Before starting work, check whether all relevant components (voltage source, connection cables,
connection terminals of the device) are de-energized using suitable measuring equipment.
• Use insulated tools (e.g. screwdrivers).
• DEVICES MUST BE GROUNDED.
Pos : 123 /Anleit ungen/El ektr onik /FU und St art er/2. M ontage und I nst allation/ Elek trischer Ans chl uss/ Elek trischer Ans chl uss _02 [SK 1xx E, SK 2x xE, SK 5xx E; -FD S, SK 500P] @ 29\m od_1551967877653_14638.docx @ 2499477 @ @ 1
Information
Temperature sensor and PTC thermistor (TF)
As with other signal cables, PTC thermistors must be laid separately from motor cables. Otherwise
the interference signals induced by the motor winding into the line will cause a disturbance in the
device.
Ensure that the device and the motor are specified for the correct supply voltage.
Pos : 124 /Anleit ungen/El ektr onik /FU und St art er/2. M ontage und I nst allation/ Elek trischer Ans chl uss/ Elek trischer Ans chl uss _Ergänz ung 1 [ SK 2xxE] @ 7\mod_1434463656020_14638. docx @ 226136 @ @ 1
In order to establish the electrical connections, remove the SK 2xxE from the SK TI4-... connection
unit (
Section 2.1.2 "Motor installation steps").
One terminal block is provided for the power connections and one for the control connections.
The PE connections (device ground) are inside the cast housing of the connection unit on the bottom.
One contact is available on the power terminal block for size 4.
Pos : 125 /Anleit ungen/El ektr onik /FU und St art er/2. M ontage und I nst allation/ Elek trischer Ans chl uss/ Elek trischer Ans chl uss _Ergänz ung 2 [ SK 1xxE, SK 2xx E] @ 8\m od_1439219159130_14638. docx @ 236274 @ @ 1
The terminal block assignments differ according to the version of the device. The correct assignment
can be found on the inscription on the respective terminal or the terminal overview plan printed inside
the device.
Pos : 126 /Anleit ungen/El ektr onik /FU und St art er/2. M ontage und I nst allation/ Elek trischer Ans chl uss/ Elek trischer Ans chl uss _Ergänz ung 3 [ SK 2xxE] @ 8\mod_1439287784030_14638. docx @ 236374 @ @ 1
Connecting terminals for
(1)
Power cable
Motor cable
Braking resistor wires
(2)
Control wires
Electromechanical brake
PTC thermistor (TF) of motor
(3)
PE
Pos : 127 /Allgem ein/ Allgem eingültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0. doc x @ 2265496 @ @ 1
