background image

 

 

REFRACTORY BRICKS REPLACEMENT 

Do not use the stove when there is a missing or broken brick. 

If a refractory brick is broken replace it by a similar one.

 

You can purchase replacement refractory bricks at your retailer or at 

Soca Industries INC. 

REFRACTORY BRICK 

 

DOOR MAINTENANCE 

Before heating the stove for the first time, it is necessary to remove all the labels and wash the door with soapy water 

(soft soap).

 

Because, the least traces on the door will remain forever when heating your stove

.

  

Clean your stove regularly by removing the ashes. Then, deposit ashes in a steel container provided with a tight lid. This 
container should not have any other type of waste in it.  

The door and the gasket must always be clean and in good condition. Perhaps for an intensive use, it will be necessary to 
replace  the  door’s  joint  if it  lost  its  elasticity.  Check the  door’s  sealing  periodically;  a  damaged or  used  joint  must  be 
replaced immediately. Contact the nearest store for spare parts. 

Note  that  solid  fuel  stoves  must  be  frequently  cleaned  because  an  accumulation  of  soot,  creosote  and  ashes  can  be 
formed. Directions must be given concerning the measures to be taken if there is a chimney fire due to an accumulation 
of soot or creosote. 

Summary of Contents for DIAMOUND INSERT


















Reviews: