NordicTrack 29822.0 User Manual Download

Page: 25 / 36

Most treadmill problems can be solved by following

the simple steps below. Find the symptom that

applies, and follow the steps listed. If further assis-

tance is needed, see the front cover of this manual.

SYMPTOM: The power does not turn on

a. Make sure that the power cord is plugged into a

surge suppressor and that the surge suppressor is

plugged into a properly grounded outlet (see page

15). Use only a single-outlet surge suppressor that

meets all of the specifications described on page

15. IMPORTANT: The treadmill is not compat-

ible with GFCI-equipped outlets and may not be

compatible with AFCI-equipped outlets.

b. After the power cord has been plugged in, make

sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

frame near the power cord. If the switch protrudes

as shown, the switch has tripped. To reset the

power switch, wait for five minutes and then press

the switch back in.

SYMPTOM: The power turns off during use

a. Check the power switch (see the drawing above).

If the switch has tripped, wait for five minutes and

then press the switch back in.

b. Make sure that the power cord is plugged in. If the

power cord is plugged in, unplug it, wait for five

minutes, and then plug it back in.

c. Remove the key from the console, and then

reinsert it.

d. If the treadmill still will not run, please see the front

cover of this manual.

SYMPTOM: The console displays remain lit when

you remove the key from the console

a. The console features a display demo mode, de-

signed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove

the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a

few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 23 to turn off the

demo mode.

SYMPTOM: The displays of the console do not

function properly

a. Remove the key from the console and UNPLUG

THE POWER CORD.

Remove the five #8 x 3/4" Screws (15). Carefully

slide the Motor Hood (65) off.

TROUBLESHOOTING

Reset

Tripped

Summary of Contents for 29822.0





































Search results

Summary of Contents for 29822.0

Reviews:

Related manuals for 29822.0

Brands by name

Popular brands

NordicTrack 29822.0, User Manual

Search results

Summary of Contents for 29822.0

Reviews:

Related manuals for 29822.0

Brands by name

Popular brands