NordicTrack 29822.0 User Manual Download

Page: 26 / 36

Locate the Reed Switch (52) and the Magnet (51)

on the left side of the Pulley (50). Turn the Pulley

until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet

and the Reed Switch is about 1/8 in. (3 mm). If

necessary, loosen the #8 x 3/4" Tek Screw (13),

move the Reed Switch slightly, and then retighten

the Screw. Reattach the Motor Hood (not shown)

with the five #8 x 3/4" Screws (not shown) and run

the treadmill for a few minutes to check for a cor-

rect speed reading.

SYMPTOM: The incline of the treadmill does not

change correctly

a. Hold down the Stop button and the Speed increase

button, insert the key into the console, and then

release the Stop button and the Speed increase

button. Press the Stop button and then press the

Incline increase or decrease button. The treadmill

will automatically rise to the maximum incline level

and then return to the minimum level. This will re-

calibrate the incline system. If the incline does not

begin calibrating, press the Stop button again, and

then press the Incline increase or decrease button

again. When the incline is calibrated, remove the

key from the console.

SYMPTOM: The walking belt slows when walked on

Use only a single-outlet surge suppressor that

meets all of the specifications described on page

15.

b. If the walking belt is overtightened, treadmill per-

formance may decrease and the walking belt may

become damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both

idler roller screws counterclockwise, 1/4 of a turn.

When the walking belt is properly tightened, you

should be able to lift each edge of the walking belt

2 to 3 in. (5 to 7 cm) off the walking platform. Be

careful to keep the walking belt centered. Then,

plug in the power cord, insert the key, and run the

treadmill for a few minutes. Repeat until the walk-

ing belt is properly tightened.

c. Your treadmill features a walking belt coated with

high-performance lubricant. IMPORTANT: Never

apply silicone spray or other substances to the

walking belt or the walking platform unless in-

structed to do so by an authorized service rep-

resentative. Such substances may deteriorate

the walking belt and cause excessive wear. If

you suspect that the walking belt needs more lubri-

cant, see the front cover of this manual.

d. If the walking belt still slows when walked on, see

the front cover of this manual.

Idler Roller Screws

2–3 in.

Top

View

1/8 in.

Summary of Contents for 29822.0





































Search results

Summary of Contents for 29822.0

Reviews:

Related manuals for 29822.0

Brands by name

Popular brands

NordicTrack 29822.0, User Manual

Search results

Summary of Contents for 29822.0

Reviews:

Related manuals for 29822.0

Brands by name

Popular brands