background image

7.

Make sure that all parts are properly tightened before you use the treadmill.

Note: If there is a thin sheet

of clear plastic on the hood decal, remove it. Keep the included allen wrench in a secure place. The allen
wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet from damage, place a
mat under the treadmill.

6. Insert two Handrail Bolts (78) with Handrail Bushings

(77) into the right Upright (69) and the right Handrail
Spacer (65). Turn the Handrail Bushings so they fit
against the Upright with the thick sides of the Bushings
toward the center of the treadmill as shown in the inset
drawing. Lift the right Handrail (66) slightly and align the
Bolts with the holes in the Handrail. Next, thread the
Bolts into the Handrail. 

Do not tighten the Bolts yet.

Attach the left Handrail (not shown) in the same way.
Tighten all four Handrail Bolts (78).

6

78

77

Thick

Side

69

66

65

77

5. Pull the Upright Wire Harness (98) up through the other

Handrail Spacer (65). Place the Handrail Spacer on the
right Upright (69) as shown, with the cutout turned toward
the treadmill (see inset drawing A). 

Have a second person hold the Handrails (66) near the
Uprights (69) as shown. Connect the Upright Wire
Harness (98) to the wires extending from the Console
Base (81). Insert the connectors and the Upright Wire
Harness into the hole in the Console Base (see inset
drawing B).

Set the Handrails (66) on the Handrail Spacers (65),
being careful not to pinch the Upright Wire Harness (98). 

5

98 69

66

81

65

69

65

81

98

A

B

7

4. Slide the Grounding Bracket (107) onto one of the

Handrail Spacers (65) in the location shown. 

See inset drawing A. Pinch the tabs on the Grounding
Bracket (107) so that the tabs will fit into the hole in the
Upright (69 [see inset drawing B]). 

See inset drawing B. Place the Handrail Spacer (65) on
the left Upright (69) as shown, with the cutout on the indi-
cated side. Note: Make sure that the tabs on the
Grounding Bracket (107 [see inset drawing A]) are in-
serted into the hole in the Upright.

4

Tabs

A

B

69

107

107

65

65

Cutout

Cutout

Summary of Contents for C 1800S































Reviews: