background image

9

HOW TO USE THE EXERCISE CYCLE

HOW TO ADJUST THE SEAT

To adjust the position of

the seat, first loosen the

adjustment knob and pull

it outward. Move the seat

forward or backward to

the desired position,

release the adjustment

knob into an adjustment

hole, and firmly tighten

the adjustment knob.

Make sure that the adjustment knob is engaged in

an adjustment hole in the seat carriage.

HOW TO ADJUST THE SEAT POST

For effective exercise, the seat should be at the

proper height. As you pedal, there should be a slight

bend in your knees when the pedals are in the lowest

position.

To adjust the height of

the seat post, first loosen

the adjustment knob and

pull it outward. Move the

seat post upward or

downward to the desired

position, release the

adjustment knob into an

adjustment hole, and

then tighten the adjust-

ment knob.

Make sure

that the adjustment

knob is engaged in an adjustment hole in the seat

post.

HOW TO ADJUST THE HANDLEBAR POST

To adjust the height of

the handlebar post, first

loosen the adjustment

knob and pull it outward.

Move the handlebar post

upward or downward to

the desired position,

release the adjustment

knob into an adjustment

hole, and then tighten

the adjustment knob.

Make sure that the adjustment knob is engaged in

an adjustment hole in the handlebar post.

HOW TO ADJUST THE PEDAL STRAPS

To tighten the pedal straps, simply pull the ends of the

pedal straps. To loosen the pedal straps, press and

hold the tabs on the buckles, adjust the pedal straps

to the desired position, and then release the tabs.

HOW TO ADJUST THE PEDALING RESISTANCE

To increase the resis-

tance of the pedals, turn

the resistance knob

clockwise; to decrease

the resistance, turn the

resistance knob counter-

clockwise.

To stop the flywheel,

push the brake lever

downward. The flywheel

should quickly come to a

complete stop.

HOW TO LEVEL THE EXERCISE CYCLE

If the exercise cycle

rocks slightly on your

floor during use, turn one

or both of the leveling

feet on the front or rear

stabilizer until the rocking

motion is eliminated.

HOW TO MAINTAIN THE EXERCISE CYCLE

Inspect and tighten all parts of the exercise cycle reg-

ularly. Replace any worn parts immediately.

To clean the exercise cycle, use a damp cloth and a

small amount of mild detergent.

IMPORTANT: To

avoid damage to the console, keep liquids away

from the console and keep the console out of

direct sunlight.

Seat

Adjustment

Knob

Adjustment

Knob

Resistance

Knob

Leveling

Feet

Adjustment

Knob

Seat

Post

Handlebar

Post

Brake

Lever

Summary of Contents for C2 Sport Bike













Reviews: