NordicTrack NTL61011.2 User Manual Download

Page: 24 / 32

Locate the Reed Switch (95) and the Magnet (44)

on the left side of the Pulley (43). Turn the Pulley

until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet

and the Reed Switch is about 1/8 in. (3 mm). If

necessary, loosen the #8 x 3/4" Truss Head Screw

(19), move the Reed Switch slightly, and then

retighten the Screw. Reattach the Motor Hood (not

shown) with the five #8 x 3/4" Screws (not shown)

and run the treadmill for a few minutes to check for

a correct speed reading.

SYMPTOM: The incline of the treadmill does not

change correctly

a. Hold down the Stop button and the Speed increase

button, insert the key into the console, and then

release the Stop button and the Speed increase

button. Press the Stop button and then press the

Incline increase or decrease button. The tread-

mill will automatically rise to the maximum incline

level and then return to the minimum level. This will

recalibrate the incline system. If the incline does not

begin calibrating, press the Stop button again, and

then press the Incline increase or decrease button

again. When the incline is calibrated, remove the

key from the console.

SYMPTOM: The walking belt slows when walked on

Use only a surge suppressor that meets all of the

specifications described on page 14.

b. If the walking belt is overtightened, treadmill per-

formance may decrease and the walking belt may

become damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both

idler roller screws counterclockwise, 1/4 of a turn.

When the walking belt is properly tightened, you

should be able to lift each edge of the walking belt

2 to 3 in. (5 to 7 cm) off the walking platform. Be

careful to keep the walking belt centered. Then,

plug in the power cord, insert the key, and run the

treadmill for a few minutes. Repeat until the walk-

ing belt is properly tightened.

c. Your treadmill features a walking belt coated with

high-performance lubricant. IMPORTANT: Never

apply silicone spray or other substances to

the walking belt or the walking platform unless

instructed to do so by an authorized service

representative. Such substances may deterio-

rate the walking belt and cause excessive wear.

If you suspect that the walking belt needs more

lubricant, see the front cover of this manual.

d. If the walking belt still slows when walked on, see

the front cover of this manual.

Idler Roller Screws

2–3 in.

Front

View

1/8 in.

Summary of Contents for NTL61011.2

































Search results

Summary of Contents for NTL61011.2

Reviews:

Related manuals for NTL61011.2

Brands by name

Popular brands

NordicTrack NTL61011.2, User Manual

Search results

Summary of Contents for NTL61011.2

Reviews:

Related manuals for NTL61011.2

Brands by name

Popular brands