Nordpeis PN-SAL01-300, Installation Manual

4 

GB

The product is not compatible with top connected 

concrete chimney.

Requirements for Floor Plate by Combustible Floor

Follow the requirements for floor plate (stone, steel, 

etc.) that apply in the country that the product is 

installed in.

Glue

The outer elements should be glued with the acrylic 

which is included. Make sure that all the surfaces that 

are to be glued are free of dust. The surfaces can be 

cleaned for better adhesion. Ensure that the surfaces 

are dry before spreading on the acrylic. Once the 

fireplace is assembled, fill the joints with acrylic and 

even it out with a sponge or finger and some soapy 

water, in order to have a clear indentation between the 

elements (FIG Z).

Minor Dents 

Transportation and handling can cause minor dents to 

the product. This can be repaired with the powder glue 

which is included. For a perfect result you can fill and 

grind with a suitable filler on top of the powder glue.  

Fill smaller cracks and uneven surfaces with a float or 

a brush. If the dent is deep, it is recommended to fill in 

several stages to avoid sinking. Even out with e.g. a 

damp sponge or  a float.

Painting

The surface of the chimney surround is developed to be 

painted without priming work. Use latex or acrylic based 

paint (emulsion paint), or cement-based textured paint. 

In the unlikely case that there are some irregularities in 

the surface, these can be filled with the acrylic which is 

included, or a light and appropriate filling material. Any 

surface that has been filled needs to be smoothened 

with fine sand paper. 

Polishing

If a more traditional and polished surface is wished for, 

it is recommended to dampen the surround and then 

cover it with tile adhesive (powder glue) and a fibreglass 

mesh, prior to possibly adding mortar or mineral polish.

Tiles

This fireplace can also be partially or completely 

covered with tiles / natural stone of your choice. As for 

the section above on “Polishing”, we recommend that 

the chimney surround is dampened before it is covered 

with tile adhesive (powder glue) and a fiberglass mesh. 

This is to ensure good adhesion and prevent the 

formation of cracks at the joints of the surround.

Maximum weight of steel chimney (top connection) 

is 350kg.

By top connection to steel chimney, we refer to the 

respective manufacturer’s installation instructions.

Please note that the adhesive and mortar must 

set before burning in the fireplace. Follow the 

instructions from the mortar/adhesive producers.

Regardless of surface treatment it is advantageous to 

mask the entire door frame to avoid having to clean it 

later.

Please note that the air gap between the surround 

and the door frame must not be filled with glue, 

mortar or similar.

Thermotte™ 

The insulation plates (Thermotte) are classified as “wear 

and tear” parts which will require to be exchanged after 

some years. 

The wear time will depend on the individual use of your 

product. 

Nordpeis offers a one-year warranty on these parts. 

After this, replacements can be purchased.

Please note:

 Wood logs that are too long can cause 

additional strain and crack the plates, due to the tension 

created between the side plates. 

Cracks in the i PowerStone

Due to thermal effects there may be small cracks / 

fissures in the PowerStone. This is natural and does not 

affect the product’s function or safety.

2. Warranty

For detailed description of the warranty conditions see 

the enclosed warranty card or visit our website 

www.nordpeis.com

Recycling of the ceramic glass

Ceramic glass cannot be recycled. Old glass, breakage 

or otherwise unusable ceramic glass, must be discarded 

as residual waste. Ceramic glass has a higher melting 

temperature, and can therefore not be recycled together 

with glass. In case it would be mixed with ordinary 

glass, it would damage the raw material and could, in 

worst case end the recycling of glass. It is an important 

contribution to the environment to ensure that ceramic 

glass does not end up with the recycling of ordinary 

glass.

Warning!

Any unauthorized modification of the appliance 

without written permission of the Manufacturer 

are prohibited.

Warning!

Use replacement parts recommended only by 

the Manufacturer.