background image

 

 

  Modem Switching by Modem Access Code

 

 
 
 
 
 
 
 

1:  Type your phone number

 

ype the letter "R" 

odem generates reverse modem tone

2:  After the phone number, t
3:  Press the Enter key 

The calling computer's m
immediately after dialing. 

 

 

There is an alternative for your 

Ultra Switch 100 to

 route a modem call to 

he Modem Access Code can be entered locally or remotely, both 

  To Enter the Modem Access Code Remotely 

struct the caller to follow the steps listed below to access your 

:Type your phone number. 

 

 

10

 

the modem port. This allows computer connection via the modems that 
do not support reverse modem communication. This approach requires 
the Modem Access Code to instruct the 

Ultra Switch 100 

that a computer 

communication is requested. The 

Ultra Switch 100

, after receiving the 

Modem Access Code (default code: 

22

, page 17), routes the line to the 

modem port through which the calling and the receiving modems are 
connected for computer communication. 
 
T
requires the code to be entered after the call is answered by the 

Ultra 

Switch 100

 

 
In
computer:  

 
1

 
 
 

 

 

Summary of Contents for ULTRASWITCH 100































Reviews: