manualshive.com logo in svg

Norstar Voice Mail 4.0, Set Up And Operation Manual

The Norstar Voice Mail 4.0 is a comprehensive communications solution for businesses. With its extensive features and user-friendly interface, this manual provides step-by-step instructions for easy set up and operation. Download the Set Up And Operation Manual for free from 88.208.23.73:8080 and maximize the potential of this innovative product.

Share
Download
background image

190

  Norstar Voice Mail Troubleshooting

Set Up and Operation Guide

P0886600 Issue 1.0

Norstar Voice Mail Error Messages

This describes the Error Messages shown when an incorrect action is performed. 
The Error Messages shown here are presented in alphabetical order.

Message

Appears

Already a member

Appears when trying to add a mailbox again to a Group List. A mailbox 
cannot be assigned to the same Group List twice.

Cannot delete

Appears when trying to delete a Special Mailbox. The System Coordinator 
and General Delivery Mailboxes cannot be deleted.

Ext assigned

Appears when the same DN is assigned twice to the same mailbox, or when 
an DN is assigned to more than one mailbox.

Extension needed

Appears when a DN has not been assigned from a transfer point.

Incomplete tree

Appears when trying to enable a Tree before all paths are added, or before 
all the mailboxes used in the Tree are initialized.

Info mailbox

Appears when trying to change an Information Mailbox from the Mailbox 
Admin Menu using Feature 983.

Intro too short

Appears when the introduction to a message being forwarded is less than 
three seconds long.

Invalid class

Appears when an incorrect Class of Service is entered while adding or 
changing a mailbox Class of Service using Feature Code 983.

Invalid ext

Appears when an incorrect DN is entered. Check the DN length or use the 
Company Directory.

Invalid glist

Appears when an incorrect Group List number was entered while changing 
or deleting a Group List number using Feature Code 983.

Invalid greeting

Appears when an incorrect Greeting Number is entered. Greeting Numbers 
must be a number from 1 to 40.

Invalid key

Appears when the selected option is not valid for the command display 
shown.

Invalid line

Norstar Voice Mail supports line numbers from 1 to 500.

Invalid mailbox

Appears when an incorrect mailbox number is entered. Also appears when a 
mailbox has not been assigned to the requested DN. These calls are 
transfered into the General Delivery Mailbox.

Invalid number

Appears when entering an incorrect line pool number, or an incorrect 
number of channels while configuring Outdialing.
Also appears when entering more than the maximum number of digits 
allowed for a phone number (maximum is 30 digits).

Invalid password

Appears when an incorrect mailbox password is entered.

Invalid path

Appears when entering an incorrect number to represent a Path. The Path 
number is a series of numbers where each number must be from 0 to 8. This 
message also appears when all Paths on a Tree are assigned. The maximum 
number of Paths for a Tree is eight on each level.

Invalid time

Appears when an incorrect time is entered in a mailbox owner’s Off-premise 
Message Notification set up. This message also appears if you specify an 
invalid time for your business hours.

Invalid tree

Appears when an incorrect number is assigned to represent a Tree. The Tree 
number must be 1, 2, 3, 4 or 5.

Invalid value

Appears when entering, or changing an incorrect amount of time for the 
DTMF delay setting. The valid DTMF delay ranges from 20 to 80 milliseconds.

Summary of Contents for Voice Mail 4.0



































































































































































































































































Reviews:

No comments

Related manuals for Voice Mail 4.0

Samsung SVM-400 General Description Manual preview
SVM-400
Brand: Samsung Pages: 40
Alternative Technologies VM8000 User Manual preview
VM8000
Brand: Alternative Technologies Pages: 3
Panasonic KX-TVA50 Installation Manual preview
KX-TVA50
Brand: Panasonic Pages: 208

Brands by name

Popular brands

Load more brands