10-10
Page 26
2006-09-15
(b) Fasten pivoting head to the sliding panel with 0.375 in. UNC x 1 in. bolt, nut and
washer assembly (factory supplied).
(c) Fasten side frame to base of manifold with 0.375 in. UNC x 1 in. bolt, nut and
washer assembly (factory supplied).
(d) Fasten pivoting heads to top of duct or air handler using bolt, nut and washer
assembly (field supplied).
NOTE
Inspect final assembly to make sure all steam tubes are fully inserted into the
grommets.
B.
OUTSIDE DUCT INSTALLATION
(1) Without Mounting Frame
(a) Once you have selected the location of the manifold, cut out a 2 in. wide slot or
2 in. dia. hole for every steam tube, to allow steam tubes to be installed.
(b) Insert all steam tubes into the main header, until flange is flush with rubber gasket.
See Figure 20. Make sure all nozzles offset each other by rotating steam tubes.
See Figure 21.
NOTES
1.
Applying water to the gasket will help to slide the steam tube into
place.
2.
Do not lift manifold by
steam tubes when
installing.
3.
Optional cover plate
to seal openings, see
Figure 25 and
Table 6.
(c) Slip steam tubes into duct.
(d) Drill four x 0.500 in. (12.7 mm)
holes at the marked locations.
(e) Fasten header to the bottom
of the duct using a bolt,
washer, and nut assembly
(field supplied).
(f)
Fasten the top steam tube
bracket to secure all steam
tubes using a bolt, washer,
and nut assembly. (Factory
supplied). See Figure 22.
(g) Fasten top steam tube bracket
to side frame using a bolt,
washer, and nut.
Figure 25. Outside Duct Mounting Cover
Plates
Summary of Contents for NH Series
