background image

AIR HANDLER

B64BM SERIES

INSTALLATION INSTRUCTIONS

IMPORTANT

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being 
able to install the product according to strict safety guidelines and instructing the customer on 
how to operate and maintain the equipment for the life of the product. Safety should always be 
the deciding factor when installing this product and using common sense plays an important 
role as well. Pay attention to all safety warnings and any other special notes highlighted in the 
manual. Improper installation of the furnace or failure to follow safety warnings could result in 
serious injury, death, or property damage.
These instructions are primarily intended to assist qualified individuals experienced in the proper 
installation of this appliance. Some local codes require licensed installation/service personnel 
for this type of equipment. Please read all instructions carefully before starting the installation. 
Return these instructions to the customer’s package for future reference.

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

Summary of Contents for B64BM Series

























Reviews: