background image

INSTALLATION CHECKLIST

10274060

(Replaces 10253260)

INSTALLER NAME:

CITY:

STATE:

INSTALLATION ADDRESS:

CITY:

STATE:

UNIT MODEL #

UNIT SERIAL #

Minimum clearances per 

page 

4

?

YES

NO

Is the unit properly installed and 

leveled?

YES

NO

Does condensate drain properly in 

both drain tubes?

YES

NO

Has the owner’s information been 

reviewed with the home-owner?

YES

NO

Has the literature package been left 

near the appliance?

YES

NO

ELECTRICAL SYSTEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Supply Voltage: ____________________________

_______

(V)

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting correct?

YES

NO

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. 
This includes being able to install the product according to strict 
safety guidelines and instructing the customer on how to operate 
and maintain the equipment for the life of the product. Safety should 
always be the deciding factor when installing this product and using 
common sense plays an important role as well. Pay attention to 
all safety warnings and any other special notes highlighted in the 
manual. Improper installation of the furnace or failure to follow safety 
warnings could result in serious injury, death, or property damage.

These instructions are primarily intended to assist qualified individuals 
experienced in the proper installation of this appliance. Some local 
codes require licensed installation/service personnel for this type of 
equipment. Please read all instructions carefully before starting the 
installation. Return these instructions to the customer’s package for 
future reference.

Specifications & illustrations subject to change without notice or incurring obligations (08/19).
O’Fallon, MO, © Nortek Global HVAC LLC 2019. All Rights Reserved.

Summary of Contents for MB7EM 3-PHASE Series

























Reviews: