background image

3.2A   PREPARING THE SPIT .......................................................

  Take off the spit from the machine by push the needle side of the spit

inside the hole (needle side on the left of the spit)

  Place the meat on the spit with the herbs and spices you have

already prepared, and use the hook to be press it.

  Put the spit with the meat in the machine.

  Secure the spit to be correct in his position by putting the square side

for good.

Now the appliance is ready to operate. All you have to do is set the desired
flame and start the rotation motor by pressing the switch.

3.0 MAINTENANCE...........................................................................................

  Before  performing  any  job  of  maintenance  is  necessary  to  close  the  gas

supply found at the top of the appliance.

  It  is  consulted  to  the  user  to  undersign  to  contract  of  maintenance  with

technical personnel that foresees at least one full check-up annually.

  We  specifically  recommend  regular  checking  to  make  sure  the  flame

regulation are clean.

  The  gate  valve  and  thermocouple  must  be  checked  at  least  once  a  year

and, if necessary, restored the protection of specific oil.

  An  accurate  observance  of  the  contained  instructions  in  this  manual  are

observed, NORTH appliances will allow perfect use for a long time.

The manufacturer cannot be held responsible for any damage caused to
property, human beings or animals due to misuse of the appliances or non-
observance of instructions included in this manual.

Summary of Contents for GAS5












Reviews: