background image

 

Table of Contents 

Equipment Protection Quick Facts ........................................................................................................................................ 1

 

Table of Contents ........................................................................................................................................................ 2

 

About Your Air Compressor ....................................................................................................................................... 4

 

Specifications .............................................................................................................................................................. 5

 

Safety Signal Words .................................................................................................................................................... 6

 

Hazard Signal Word Definitions ............................................................................................................................................ 6

 

Initial Set-Up ................................................................................................................................................................ 7

 

Step 1. Inspect & Unpack ........................................................................................................................................................ 7

 

Step 2. Assembly ..................................................................................................................................................................... 7

 

Step 3. Select Suitable Location ............................................................................................................................................. 8

 

Operation ..................................................................................................................................................................... 9

 

Follow Operation Safety Rules ............................................................................................................................................... 9

 

Prepare for Operation .............................................................................................................................................................. 9

 

Check/Add Oil to the Pump ................................................................................................................................................... 9

 

Proper Air Hose and Tool Use .............................................................................................................................................. 10

 

Pressure Control Related Devices ...................................................................................................................................... 10

 

Compressor - Tool Requirements ....................................................................................................................................... 10

 

Attaching/Disconnecting Air Hose and Tools ...................................................................................................................... 10

 

Using Compressor for Spraying ........................................................................................................................................... 11

 

Flammable Materials ........................................................................................................................................................... 11

 

Moisture in Compressed Air ................................................................................................................................................ 11

 

Shutdown ............................................................................................................................................................................... 11

 

Procedure ........................................................................................................................................................................... 11

 

For Malfunction During Operation ....................................................................................................................................... 11

 

Maintenance & Repair ............................................................................................................................................... 12

 

Maintenance Schedule Summary ............................................................................................................................. 12

 

Detailed Instructions – Maintenance & Repair ........................................................................................................ 12

 

Inspect Safety/Relief Valve ................................................................................................................................................. 12

 

Inspect Air Filter .................................................................................................................................................................. 12

 

Inspect Compressor for Air Leaks ....................................................................................................................................... 12

 

Change Pump Oil ................................................................................................................................................................ 13

 

Drain Receiver Tank and Inspect Tank ............................................................................................................................... 13

 

Check Drive Belt for Tension and Alignment....................................................................................................................... 13

 

Keep Compressor Clean ..................................................................................................................................................... 13

 

Cylinder Head Bolt Torque Specification............................................................................................................................. 14

 

Troubleshooting ........................................................................................................................................................ 15

 

Parts Explosions – Model 25653 Rev A ................................................................................................................... 16

 

Parts List – Model 25653 Rev A ................................................................................................................................ 17

 

Parts Explosions – Model 25654 Rev A ................................................................................................................... 18

 

Parts List – Model 25654 Rev A ................................................................................................................................ 19

 

788876 Pump Explosion ........................................................................................................................................... 20

 

788876 Pump Parts List ............................................................................................................................................ 21

 

788876 Pump Kits ...................................................................................................................................................... 21

 

Summary of Contents for 25653

























Reviews: