background image

 

        

LineTro110Tµr User Guide  

June 2011               Page 13 of 16 

8.

 

DIMENSIONS 

 

 

 

 

 

 

 

 

 

Figure 12: LINETROLL 110Tµ/110Tµr physical 
dimensions. All figures in mm. 

9.

 

MOUNTING. 

 
LINETROLL 110E

 mounts directly on the 

high voltage conductor using a shotgun type 
Hot-stick as shown in fig 14. It should be 
mounted as close as possible to a traverse to 
escape line vibrations.  
 
 
 
 
 
 
 
 
 

 
 
Figure 14Hot-stick mounting, - close to the traverse 

 
To fully cover all kinds of faults, 
NORTROLL recommend mounting 
indicators on all the phases in multi-phase 
networks. Locate the indicators at strategic 
points along the line. 

 

9.1 Before mounting. 

Make sure the indicator is programmed (see 

4.7 Programming

) and battery connected 

before mounting on the line. 

 

9.2 Live-line mounting by using a 

Grip-

All-Clamp 

(shot-gun) Hot-Stick: 

 

1.

 

Fix the indicator to the hot-stick 
and raise/lift it to the line as shown in 
fig 14.  

2.

 

Pull the stick downwards and 
against the line, until the line is in the 
correct position within the clamp, see 
fig 15. 
Release the Grip-All-Clamp stick. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 15: Mounting using  Grip-All clamp hot stick 

 

9.3 Removal.

 

 

1.

 

Fix the claw in the “eye” on the 
horizontal part of the line-clamp, see 
fig 15. 

2.

 

Pull down, to release the indicator 
from the line.

 

 

 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
Figure 16: Removal from the line. 

 
 
 

158 mm 

 

Summary of Contents for LineTroll 110Tmr

















Reviews: