background image

2

ELECTRICAL SAFETY  

This manual contains important 
safety and operating instructions 
for your battery charger (sold 
separately).
› Before using the charger, read all 
instructions and cautionary markings 
on charger, battery pack and product 
using the battery pack.

› The charger is not intended for 
any uses other than charging 
rechargeable batteries. Any other

use may result in risk of fire, electric 
shock or electrocution.
› Do not place any object on top of the 
charger or place the charger on a soft
surface that may result in excessive 
internal heat. Place the charger in a
position away from any heat source.
› To reduce risk of damage to the 
electric plug and cord, pull by the 
plug rather than the cord when 
disconnecting the charger.
› Make sure cord is located so that it 
will not be stepped on, tripped over, or
otherwise subjected to damage or 
stress.
› An extension cord should not be used 
unless absolutely necessary. Use of an 
improper extension cord could result 
in the risk of fire, electric shock or 
electrocution.
› Do not operate charger if it has 
received a sharp blow, been dropped 
or otherwise damaged in any way. Have 
it checked by an electrician or power 
tool repairer.
› Do not disassemble charger. Take it to 
an electrician or power tool repairer
when service or repair is required. 
Incorrect reassembling may result in 
a risk of electric shock, electrocution 
or fire.
› To reduce risk of electric shock, 
unplug charger from the outlet before
attempting any cleaning. Removing the 
battery pack will not reduce this risk.
› Never attempt to connect 2 chargers 
together.

SAFETY 

CAUTION: 

Read the operating 

instructions to reduce the risk 

of inquiry.

DOUBLE INSULATED

This tool is double insulated 

in accordance with AS/NZS 

60335-1; therefore no earth wire 

is required.

DANGER! 

If the battery case is 

cracked or damaged, do not insert
into charger. There is a danger of 
electric shock or electrocution.

Warning: 

Do not allow any liquid to 

get inside charger. Electric shock 
may result. To facilitate cooling of 
the battery pack after use, avoid 
placing the charger or battery pack 
in a warm environment such as in 
a metal shed, or an uninsulated 
trailer.

!

!

Summary of Contents for NG-55













Reviews: