background image

novaG-A 

 

Manual Service 

 

3/25 

1.2 Issue  

Ref. NR-00016-ENG 

 

 

All of the information provided in this Service Manual has been included in the confidence that it 
is true, although it does not constitute any responsibility or implicit or explicit guarantee. NOVAG 
reserves  the  right  at  any  time  without  forewarning  to  make  all  necessary  improvements  and 
modifications  to  this  Service  Manual  in  order  to  rectify  any  possible  typographical  errors, 
increase  the  information  contained  and  enter  the  changes  made  to  the  characteristics  and 
performances of the gun. 

 

 

This chapter contains important information on safety, handling and use of your 

novaG-A 

gun.

 

 

Before  installing  and  operating  the  gun,  carefully  read  the  technical  and 
safety  documentation  in  this manual.  Special  attention  should  be  paid  to 
the  information  for  knowing  and  understanding  the  handling  and 
conditions of use of the gun. All of the information is aimed at enhancing 
User Safety and avoiding possible faults due to incorrect use of the gun. 

WARNING!

 

establishes  information  for  alerting  you  on  the  situations  which  could 

cause serious injury if the instructions are not followed. 

PRECAUTION!

 

establishes information which indicates how to avoid damage to the 

gun and how to avoid a situation which could cause minor injuries. 

NOTE

 is relevant information on the procedure being carried out. 

Careful  study  of  this  manual  will  help  you  to  become  more  acquainted  with  the  gun  and  the 
procedures. Following the instructions and recommendations here will reduce the potential risk 
of  accidents  in  installing,  using  or  maintaining  the  gun,  and  will  give  you  the  problem-free 
operation  for  a  longer  time,  greater  output  and  the  possibility  of  detecting  and  resolving 
problems quickly and simply.  

Keep this Service Manual for future consultation of useful information at all times. If you lose the 
manual,  ask  for  a  new  copy  from  your  local 

NOVAG

  distributor  or  make  direct  contact  with 

NOVAG SPRAY EQUIPMENT, S. A

WARNING:

 The gun's design and configuration do not allow it to be used in potentially 

explosive atmospheres or to exceed the pressure and temperature limits described in the 
technical specifications of this manual. 

Always use liquids and solvents that are compatible with the unit. In the event of doubt, consult 
the 

NOVAG

 technical service. 

 

SAFETY AND HANDLING 

Summary of Contents for novaG-A Series


























Reviews: