DL-4
plus
™
This guide provides the
basic information you need
to setup and begin using
your new DL-4
plus
. For
more detailed information
on the installation and
operation of your receiver,
please refer to the user
manuals provided on the
accompanying CD. To order a printed copy of the manuals, free
of charge, follow the instructions given on the enclosed
User
Manuals
card.
The DL-4
plus
, with 2.200 firmware or higher, provides a USB
connection through its COM1 port. The USB drivers, along with
installation instructions, are available in the USB Drivers
directory of the CD provided.
BOX CONTENTS
In addition to this
Quick Start Guide
, the following is provided
with your DL-4
plus
:
•
1 CompactFlash
™
card
•
1 12V power cable, 1 I/O cable, 1 USB cable, 1 null
modem cable, 1 straight through serial cable)
•
1 CD containing:
•
An installation program for NovAtel’s GPS PC
utilities, including
GPSolution
®
and
DL4Tool™
•
Product documentation, including user manuals
•
The
OEM4 Software Development Kit
•
DL-4plus LCD Menus Quick Look
•
OEM4 Family Quick Reference Guide
•
User Manuals
card for requesting printed manuals
ADDITIONAL EQUIPMENT REQUIRED
The additional equipment in this list is needed for a basic setup:
•
A Windows-based PC with an RS-232 DB-9 port
•
A quality GPS antenna, like NovAtel’s GPS-702
•
An antenna RF cable with a TNC male connector at the
receiver end, such as NovAtel’s C016 model
•
One of the following:
•
A standard 12 VDC automobile power outlet, or
a 7 - 18 VDC power supply capable of at least
4.0 W and a power cable with a 4-pin LEMO
plug (LEMO part number
FGG.0B.304.CLAD52Z) at the receiver end
1
SETTING UP YOUR DL-4
plus
Complete the steps below to connect and power your DL-4
plus
.
1.
Mount the GPS antenna on a secure, stable structure with
an unobstructed view of the sky.
2.
Insert the provided CompactFlash card into the slot provided
behind the door on the front face of the DL-4
plus
. Open the
door by loosening the screw at the right end.
3.
Using the antenna RF cable, connect the GPS antenna to
the
GPS
port, which is found on the DL-4
plus
back face.
4.
Connect the
COM1
port on the receiver to a serial port on
the PC, using the provided serial or USB cable.
5.
Connect the power cable to the
PWR
port by lining up the
red mark on the receiver connector with the red mark on the
cable connector.
6.
Plug in a user-supplied adapter and/or connect and turn on
the power supply. When the DL-4
plus
is properly powered,
the
PWR
LED is red.
7.
Press the
button on the front face of the DL-4
plus
.
COMPACTFLASH CARD
You may get a DISK ERROR message on the LCD screen of the
DL-4
plus.
If so, enter the following using
GPSolution
:
DISK FORMAT
Wait a few minutes until the error message is gone. Use the DL-
4
plus
power button to turn it off and then on again. When power
is returned, the DL-4
plus
should be able to use the flash card.
INSTALLING THE PC UTILITIES
Once the DL-4
plus
is connected to the PC, antenna, and power
supply, install NovAtel’s GPS PC utilities
.
1.
Start up the PC.
2.
Insert the accompanying CD in the CD-ROM drive of the
computer.
3.
Install the PC utilities by advancing through the steps
provided in the
NovAtel GPS PC Utilities
setup utility. If the
setup utility is not automatically accessible when the CD is
inserted, select
Run
from the
Start
menu and select the
Browse
button to locate
Setup.exe
on the CD drive.
CREATING A LOG GROUP USING DL4TOOL
Log groups are sets of logs to be captured by the DL-4
plus
. A
group can be created in
DL4Tool
and then downloaded to the
DL-4
plus
.
1.
Launch
DL4Tool
from the
Start
menu folder specified during
the installation process. The default location is
Start
|
Programs
|
OEM4 PC Software
.
2.
Select the
Group Editor
button.
Within the
Group Editor
, pre-defined log groups are provided
for use during common operational modes. In addition, five
empty log groups are provided. Both the pre-defined and
empty log groups are editable.
3.
Select
LOGGROUP1
from the
Group Name
drop-down list
and, if desired, use the
Rename...
button to rename the
group.
QUICK START GUIDE
1. If an alternative power source is preferred, the automobile power
adapter can be cut off from the power cable. The exposed wires
(red and orange for positive, brown and black for negative) can
then be tied to a 7-18 VDC supply capable of at least 4.0 W. The
use of a 3 A slow-blow fuse is recommended.
