Novellini Sense 7 Z2, Instructions For Installation, Use And Maintenance Manual

-60-

If button 6 is a steady red, this means the level of disinfectant in the tank must be 
topped up. 
The disinfection cycle then starts. The pump starts up for about four minutes then stops. 
After about 20 minutes, button 6 and the surround of button 2 stop flashing. Button 6 
becomes a steady red indicating that the cycle has ended and the bath must be emptied. 
In case of necessity, press button 5 to interrupt the disinfection cycle. Button 6 will 
continue to flash in red until the panel goes off to indicate that disinfection has not 
been completed. 
When emptied, the bath is ready for use. 

Cromolight:

When button 3 is pressed, it lights up in red, green or blue, activating a variable 
programme, and the spotlight comes on. 
Pressing button 3 a number of times obtains various programmes until the Cromolight 
is turned off. 
At the end of the available programmes, button 3 flashes to indicate the function is 
about to go off. 
To stop the function, hold button 3 down for a few seconds. 

Emptying the Airpool system:

After the bath has been emptied, to ensure hygiene, the water remaining in the Airpool 
jets must be eliminated. Baths with an Airpool function are therefore fitted with a 
manual/automatic drain system. 
When an Airpool or Whirlpool jet function has been activated, the system drains 
automatically. After the bath has been emptied and about 30 minutes after the panel 
goes off, the blower starts up for one minute to expel the residual water. 
If a jet function has not been used, the system must be drained manually. After emptying 
and with the bath in stand-by (panel backlit), press button 4 for a few seconds until the 
blower starts up. After one minute it goes off automatically. 
To disable all active functions with a single command, press button 5.
Pressing button 5 again turns the bath from stand-by to off. 
It shuts down automatically if not used for 30 minutes.

ADJUSTING JET NOZZLES

:

Turn the jet nozzles (C) as required. The nozzles can be turned in any direction. Make sure 
that the nozzles are not clogged and are not directed upwards (otherwise water will be 
splashed out of the tub when the system is switched on). Fill the tub until the water is 
well over the level of the jet nozzles (see illustration). After getting into the bath, the 
water level must be as shown in the illustration, otherwise the jets system may not 
start. The system features a level sensor which prevents the jets from switching on if 
there isn’t enough water in the bath. When the jets system is on, do not use foaming 
agents such as bubble baths, soap, etc.

HOW TO USE YOUR WHIRLPOOL BATH CORRECTLY:

The benefits of a whirlpool massage:
The swirling water of a whirlpool bath is naturally soothing and offers many therapeutic 
benefits. In spas, hydrotherapy is used to stimulate blood circulation, relax muscles 
and restore tone to the skin. Basically, it consists in injecting air into controlled jets of 
water of varying intensity directed at the body. The jet of warm water and air bubbles 
against the body dilates blood vessels and increases the flow of blood to the heart. In 
addition, the continuous jet of water has a massaging effect on the muscles and dilates 
skin pores, promoting the removal of toxins and helping to hydrate the surrounding 
tissue. Hydromassage is widely used by sports people to relieve tired muscles after 
strenuous physical activity, producing a pleasant sense of relaxation and well-being. 
The jet nozzles can be adjusted to direct the jets at the parts of the body where you want 
to concentrate the massaging action. The temperature of the bath water must never 

exceed 45°C. The maximum benefits are obtained with a temperature of 36°-37°C.

CLEANING AND DISINFECTION:

Deposits of organic material that collect in the pipes during a whirpool bath promote 
bacterial growth and, if left untreated, cause unsanitary conditions and unpleasant 
odours. For perfect hygiene, the jets system should be disinfected immediately after 
bathing, before draining. To disinfect, use 50 g of ordinary disinfectant (for example, 
liquid bleach) for every 100 litres of water (approximately half a glass in a bath filled 
to optimum level). Run the system for few minutes to circulate the disinfectant in the 
pipes. Stop the system, allow to soak for 15/20 minutes, then drain the bath. If the bath 
develops unpleasant odours after a long period of inactivity, it’s a good idea to disinfect 
the system before using it again. For hygiene, if the bath is used consecutively by two or 
more people, the system should be disinfected after each use. During disinfection, turn 
off the air control to reduce foaming.

MAINTENANCE AND CLEANING:

The bath is made of acrylic and must be cleaned using a liquid detergent and a soft cloth 
or sponge. Use a good quality household liquid detergent. To prevent scale deposits, 
wipe dry using a chammy leather or a soft lint-free cloth that removes stubborn 
deposits without leaving traces. Limescale deposits may be removed using specific 
detergent products. To restore shine to the acrylic surface polish with an ordinary wax 
polish such as car wax.
DO NOT USE ABRASIVE CLEANERS, ALCOHOL OR ALCOHOL BASED PRODUCTS, ACETONE 
OR OTHER SOLVENTS.

Warning: 

use of detergents other than those recommended may damage the bath 

and/or the whirlpool equipment.

SURFACE SCRATCHES:

Small surface scratches can be removed using wet emery paper (grade 1000) and then 
smoothing the surface with abrasive paste. Once the scratch has been removed, restore 
surface shine using wax polish.

TROUBLESHOOTING:

In the event of a problem, perform the following checks before activating the warranty 
or contacting qualified staff.

If the jet system does not start:

•  If the circuit breaker has tripped, reset it and try switching on the jet system again. 
•  If the pump does not start when the water level is well above the nozzles.
•  Check to ensure that the cut-out is turned on.

If the jet system does not stop:

•  If the pump continues running and cannot be turned off using the usual controls, turn 

it off using the circuit breaker and try again.

Do not make adjustments to the wiring or other electrical parts.

DISPOSING OF THE WHIRPOOL BATH:

For the disposal of the product or its parts, follow the local regulations on matters of 
waste disposal. For Italy, Legislative Decree n. 152 of April 3, 2006 will hold, and for the 
other EU countries, Directive 2008/98/EC.

PRODUCT GUARANTEE:

All products purchased by consumers, as defined in Article 3 of the Consumer Code 
(Legislative Decree no. 206 of 6 September 2005 and subsequent amendments), 
are covered by the legal guarantee of the seller under Article 128 and subsequent 
amendments of the consumer Code. In case of lack of conformity of the product, we 
invite the consumer to contact their dealer within the statutory deadline.

EC DECLARATION OF CONFORMITY:

The manufacturer Novellini S.p.a. Via Mantova, 1023 - 46030 Romanore di Borgo 
Virgilio, Mantova - Italy Declares under its responsibility that the following products:

ENGLISH