-16-
water of varying intensity directed at the body. The jet of warm
water and air bubbles against the body dilates blood vessels
and increases the flow of blood to the heart. In addition, the
continuous jet of water has a massaging effect on the muscles and
dilates skin pores, promoting the removal of toxins and helping
to hydrate the surrounding tissue. Hydromassage is widely used
by sports people to relieve tired muscles after strenuous physical
activity, producing a pleasant sense of relaxation and well-being.
The jet nozzles can be adjusted to direct the jets at the parts of
the body where you want to concentrate the massaging action.
The temperature of the bath water must never exceed 45°C. The
maximum benefits are obtained with a temperature of 36°-37°C.
CLEANING AND DISINFECTION:
Deposits of organic material that collect in the pipes during a
whirpool bath promote bacterial growth and, if left untreated,
cause unsanitary conditions and unpleasant odours. For perfect
hygiene, the jets system should be disinfected immediately
after bathing, before draining. To disinfect, use 50 g of ordinary
disinfectant (for example, liquid bleach) for every 100 litres of
water (approximately half a glass in a bath filled to optimum
level). Run the system for few minutes to circulate the disinfectant
in the pipes. Stop the system, allow to soak for 15/20 minutes,
then drain the bath. If the bath develops unpleasant odours
after a long period of inactivity, it’s a good idea to disinfect the
system before using it again. For hygiene, if the bath is used
consecutively by two or more people, the system should be
disinfected after each use. During disinfection, turn off the air
control to reduce foaming.
MAINTENANCE AND CLEANING:
The bath is made of acrylic and must be cleaned using a liquid
detergent and a soft cloth or sponge. Use a good quality
household liquid detergent. To prevent scale deposits, wipe dry
using a chammy leather or a soft lint-free cloth that removes
stubborn deposits without leaving traces. Limescale deposits
may be removed using specific detergent products. To restore
shine to the acrylic surface polish with an ordinary wax polish
such as car wax.
DO NOT USE ABRASIVE CLEANERS, ALCOHOL OR ALCOHOL
BASED PRODUCTS, ACETONE OR OTHER SOLVENTS.
Warning: use of detergents other than those recommended
may damage the bath and/or the whirlpool equipment.
SURFACE SCRATCHES:
Small surface scratches can be removed using wet emery paper
(grade 1000) and then smoothing the surface with abrasive
paste. Once the scratch has been removed, restore surface shine
using wax polish. For the best results, contact your nearest
authorised service centre.
TROUBLESHOOTING:
In the event of a problem, perform the following checks before
calling the service centre.
If the jet system does not stop:
• If the pump continues running and cannot be turned off using
the usual controls, turn it off using the circuit breaker and try
again. If the problem persists, contact the service centre.
Do not attempt to make adjustments to the wiring or
other electrical parts under any circumstances. Always
contact your nearest service centre.
DISPOSING OF THE WHIRPOOL BATH:
To dispose of the whirlpool bath or any part of it, follow local
waste disposal regulations. In Italy, Legislative Decree No. 22
of 5 February 1997 applies. In other EU countries, the subject is
governed by directives 91/156/EEC, 91/689/EEC and 94/62/EC.
PRODUCT GUARANTEE:
The product is guaranteed as per Italian Presidential Decree
224 of 24/05/1988 in Italy and the rest of the EU and as per CEE
Directive 85/374 in terms of product liability.
The Manufacturer guarantees its products against manufacturing
and material defects – provided these are confirmed by the
authorised personnel of the Company – for a period of 24 months
from the purchase date, as indicated by the receipt or invoice.
The guarantee covers repairs to and/or replacement of the parts
considered to be faulty. The guarantee does not cover complete
replacement of the product. The guarantee does not cover the
lights, warning lights, fuses, glass parts, mirrors and decoration
parts unless these are faulty due to production defects and not
due to neglect or improper use. The guarantee does not cover
any parts and components which are faulty or damaged due
to negligence or carelessness during use, incorrect installation
or maintenance, operations carried out by non-authorised
personnel, damage caused during transport or any other
circumstances not due to product manufacturing defects, such
as sudden electricity jolts, lightning, electrolysis, corrosion and,
in general, any causes related to the nature of the water and
electrical and water supply systems in the place where the
unit is used. The Purchaser must check that the product is not
damaged in any way before installation and must contact the
agent or authorised assistance centre immediately if any faults
are detected. The guarantee will only be applied on presentation
of a document indicating the purchase date.
In the event of operations without proven defects or to illustrate
how to use the product, all the expenses are sustained by the
Purchaser. Any repairs or modifications carried out by personnel
not authorised by the Manufacturer will not be covered by the
guarantee and will render the remaining guarantee period
immediately null and void.
The Manufacturer is not responsible in any way for any direct
or indirect damage caused to persons, animals or things due
to failure to comply with all the regulations in the installation,
instruction and maintenance manual supplied with the product.
Any disputes will be dealt with exclusively by Mantova Italy, Law
Court.
EC DECLARATION OF CONFORMITY:
The manufacturer Novellini S.p.a. Via della Stazione, 2 46030
Romanore di Borgo Virgilio, Mantova - Italy Declares under its
responsibility that the following products:
whirlpool baths mod. 500/10 500/20 500/30 700/10 700/20
700/50 700/60 are in conformity with the following European
directives: 2006/95/CE, 2004/108/CE and EU regulation
305/2011 and subsequent amendments, with reference to
harmonized standards:
EN55014-1
EN55014-2
EN60335-2-60
EN12764
ENGLISH
