background image

 

 

5

 

2.3 

SAFETY FEATURES  

The sterilizer features several devices that assure the full safety for the operators. 

 

Door with dual lock control 

An electromechanical device allows the door to be opened only if the following conditions are met: 

unit power supplied and turned on 

no current alarms 

internal pressure not dangerous for the operator 

For  further  safety,  to  unblock  the  door  at  the  end  of  cycle  or  in  case  of  alarm  it  is  necessary  to  press  the 
Start/Stop button. 

 

Attention: If the equipment is turned off with the door open, do  not  apply  force  on 
the handle to try closing the door. To close it, the equipment must be on. 

 

 

Protection against overpressure 

– safety and decompression valves 

 

Safety  valve  -  it  takes  over  when  the  pressure  inside  the  chamber  exceeds  the  value  of  2,55  bar.  To 
verify  the  efficiency  of  the  valve,  when  the  unit  is  cold  and  switched  off,  unscrew  the  black  cap  of  the 
valve, when a “click” is heard pull it gently : you have to feel that the cap is free to move. The valve can 
not  be  adjusted  or  serviced  for  safety  reasons.  Follow  the  maintenance  program  described  in  the  ap-
pendix SERVICE BOOK to assure the safety of the unit. 

 

Decompression valve 

– it takes over when the pressure inside the chamber exceed the value of 2,4 bar; 

an acoustic signal warns the operator and the display shows the message ALARM 10. 

 

Overheating protection 

The temperature inside the chamber is programmed so as not to exceed the limit of 142 °C; in case of fault, 
a further protection takes over to prevent the temperature from rising over 150 °C. 

 

Blackout protection 

In  case  of  power  blackout  during  the  sterilization  cycle,  the  pressure  inside  the  chamber  is  completely  re-
leased to the drain valve. On power supply restore, the display will show the message BLACK OUT. 

 

Automatic switch off 

Elapsed 30 minutes from the end of the cycle without opening the door or activating a front panel button, the 
unit will automatically switch off.  

 

This function is not operating if no sterilization cycle has been carried out and completed

.

 

 

Summary of Contents for iClave Plus





































Reviews:

Related manuals for iClave Plus