background image

Daily Maintenance (continued) 

x

  Empty the filter bag daily or when it is 

approximately one-half (1/2) full. 

Charging Batteries 

x

  Recharge the batteries when indicated by the 

Battery Meter. 

x

  Check charger cord for exposed wires and 

damaged plugs before using.  

x

  To recharge the batteries plug the charger cord into 

the charger located on top of the machine and then 
into an electrical outlet. 

x

  When the cord is plugged into an outlet the 

machine will automatically become disabled. 

x

  Charge the batteries with the cover open when 

possible to reduce heat build up in the batteries. 

x

See charging instructions for more details. 

x

ALWAYS

 wear eye protection, rubber gloves and 

protective clothing to avoid contact with battery 
acid when working around batteries. 

x

  After charging batteries check the water level of 

each battery cell and add distilled water as 
required to level specified by battery manufacturer.  

x

  Check and verify that all battery connections are 

clean and tight. 

x

  Wipe machine down with a damp cloth. 

x

NEVER

spray this machine with water or any 

liquids. 

x

ALWAYS

 Check the tilt switch for proper 

operation. With the master switch turned off, put 
the brush head into the pad change position. Turn 
the brush switch on then the master switch on, the 
machine should turn on.  

x

  If the machine does not turn on and the battery 

meter is flashing a one, the tilt switch has failed. 

DO NOT

 use the machine until the tilt switch has 

been replaced. 

Weekly Maintenance               
(Every 25 Hours) 

Verify all daily maintenance has been performed. 

x

  Inspect the Flexiwall Shield for dents around the 

outside edge and cracks in the plastic.  

x

  Check that the Brush and Retaining Band are 

properly installed.  

x

  Remove dirt build up on the brush along the 

bottom of the Flexiwall Shield. 

x

  A damaged Flexiwall Shield Assembly will greatly 

reduce dust control capabilities of the machine. 

Monthly Maintenance   
(Every 100 Hours) 

Verify that all daily and weekly maintenance has 
been performed. 

x

  Check the Battery Tray Drain Hose for liquid level 

on a monthly basis. 

x

  Spilled liquids from the battery compartment area 

are collected in a tray under the batteries. The tray 
can be drained using the hose at the right rear of 
the machine as shown above.  

x

IMPORTANT:

 Drain all liquids into an approved 

container and dispose of according to your local 

EPA regulations

.

https://harrissupplyind.com - To Order Parts Call 608-268-8080

Summary of Contents for CHARGER 2717 DB













Reviews: