background image

NTI RACKMUX-V

15/17

  RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE 

 

15

 

DISPLAY FUNCTIONS 

An NTI RACKMUX with a 17” monitor supports resolutions up to SXGA (1280 x 1024) and a 15” monitor supports resolutions up 
to XGA (1024 x 768), each with a refresh rate at between 55 and 76Hz.  The quality of the image on the LCD monitor is adjustable 
using an On Screen Display (OSD) menu using the control buttons on the RACKMUX.     

Standard Controls 

 

The RACKMUX has 5 standard control buttons and a power LED. The 5 standard control buttons operate as follows: 

 

 

The 

Power

 button turns the RACKMUX LCD and backlight ON and OFF as desired.    

 

 

The 

Power LED

 located immediately below the Power button is a dual color  

        LED.  It will illuminate with a green color when the RACKMUX is powered  
        ON and working properly.  It will illuminate with a red color if the RACKMUX  
        is powered ON but there is no input signal detected.     
 

 

The 

Menu

 button is used to bring up the OSD menu where the various 

settings of the LCD display can be adjusted.  Once the OSD screen is 
displayed,  the Menu button is used to make selections within the menus.    
See "OSD Control Menu" (below) for more on LCD display settings. 

 

 

The 

Up and Down Arrow

 buttons are used to navigate through the menus.   

Move the cursor up or down as desired to highlight an item for selection.    

        Once an item is highlighted, pressing the Menu button will select it.    

                             Figure 20- OSD Controls 

 

The 

Select 

button is used to make selections within the OSD menus when  the OSD menu is ON.  When the OSD menu is 

OFF, the Select button will act as an 

Auto Adjust

 button to keep the user from having to use the menus to adjust the quality 

of the image on the monitor.   

 
 

OSD Control Menu- 15 and 17 Inch VGA models (-V15/-V17) 

 
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display.  To activate the 
OSD Menu,   press the 

Menu

 button (above).  To turn the Menu back OFF, either select "EXIT" from the main menu or just wait  

10-60 seconds and it will automatically be cleared from the screen.     

OSD Main Menu 

 
 
 
 
 
 
 
 
 
 
 

Selection 

Purpose 

Range 

Brightness/Contrast Increase/decrease 

panel brightness/contrast level 

1-100 

Color 

R,G,B color temperature control 1-100 

Position 

 

Video Image horizontal and vertical position control 

 

Clock setting 

 

Phase control 

1-100 

Setup 

 

Control OSD Image position on screen 

 

Set time OSD will stay on screen before auto shutoff 

 

Select the language of the OSD menu  

-- 
10 to 60 seconds 
Several languages (see page 8) 

Exit 

Exit from the OSD control menu 

 

 
 
 

Power
ON/OFF

Menu

Up Arrow

         Select/
Auto Adjust

Power LED

Down Arrow

Controls for the
OSD Menus

Summary of Contents for RACKMUX-D17



































Reviews: