9
Monitor Outside Width
Outer Width of Monitor
0~65000 (0.1mm)
0
X
9
Monitor Outside Height
Outer Height of Monitor
0
X
9
Monitor Viewable Width
Width of Viewable Area
0
X
9
Monitor Viewable Height
Height of Viewable Area
0
X
100
Stretch Type
Screen Stretch Type
0 = Auto
1 = Stretch Out
2 = Fit In
2
X
101
Rotate
Screen Rotation and Mirror
0 ~ 7
0
X
102
Vertical Shift
Screen Vertical Shift
400 = Default
399 ~ 0 = shift up
401 ~ 801 = shift down
400
X
103
Horizontal Shift
Screen Horizontal Shift
400 = Default
399 ~ 0 = shift left
401 ~ 801 =shift right
400
X
104
Vertical Scale
Screen Vertical Scale
0 ~ 255
0
X
105
Horizontal Scale
Screen Horizontal Scale
0
X
106
Load Video Wall
Load Video Wall Setting
0~15
V
X
107
Save Video Wall
Save Video Wall Setting
V
X
200
Backup Setting
Backup Setting to bank 0~3
0 ~ 3
V
V
201
Restore Setting
Restore Setting from bank 0~3
V
V
202
System Setting
System Setting
0~255 (For debug use, not
recommended for general users)
V
V
203
Application Setting
Application Setting
V
V
333
Reset To Default
Reset to factory default
V
V
999
System Reboot
System Reboot
V
V
V = Available X = Not available Numbers = default value
Caution when using IR Menu:
Menu 17
Free Routing function only works in Multicast mode.
Menu 22
When the USB extender function is disabled it will also disable the keyboard/mouse function.
Menu 25
Displays or hides the TV wall setting in the webpage.
Menu 27
You could disable keyboard/mouse extender if there are any compatibility issues, and instead use the “USB” ports
instead of “KEYBOARD MOUSE” ports.
Menu 33
To customize the IR remote, you need to be use RS232 commands described later in this manual
Menu 35
For monitors that detect HDMI 5V causing them to enter sleep mode.
Menu 36
Turn OFF monitor by CEC command via RX.
Menu 40
In VGA/DVI dual input mode:
When input video loss exceeds 8 seconds the Transmitter will switch to another input automatically.
When the input is from DVI source, the Transmitter will convert DVI to VGA loop out automatically.
Menu 41 Pass-Through
= the output resolution is determined by the Transmitter EDID,
Auto Detect (Per EDID)
= the output resolution is determined by the monitor EDID connected to the Receiver
Customize=
resolution needs to be setup using RS232 command or web page
Menu 47
Use default EDID at Transmitter side, or copy monitor EDID at Receiver side. (In Multicast mode)
Menu 48
Copying the EDID from the monitor connected to the Transmitter is not supported.
Menu 49
Monitor HDCP version setting, with incorrect HDCP version setting a black screen will display.
Option
Description
Disable
HDCP version follows source and Stream Type of content
HDCP 1.4 Always On
Monitor supports HDCP 1.4
HDCP 2.2 Always On
Monitor supports HDCP 2.2
Menu 50
Extender = RS232 extender,
Keypad = for RS232 keypad or number key in terminal software,
Auxiliary = auxiliary mode debug,
Console = system console debug
Menu 60
Fast Switch mode works best when all parameters on all units are the same: resolution, frame rate, scan mode
(interlaced/non-interlaced), color depth, color space, interface (HDMI/DVI), HDCP mode (ON/OFF).
Disable:
Stop a link before switching a channel, a black screen will appear between switching. If you switch to a channel that
doesn’t exist it will show diagnostic Information.
Enable:
Keep the link when a channel is switched. If you switch to a channel that doesn’t exist, the screen may freeze for
1~2 seconds and then show diagnostic Information.
13