background image

P3245-1M

 

Multimeter digital, True RMS

 

 

 

 

2.

 

Quick Start   

 

General Inspection 

 

After you get a new multimeter, make a check on the instrument according to the 
following steps:   

1.  Check whether there is any damage caused by transportation.   

If it is found that the packaging carton or the foamed plastic protection cushion has 
suffered serious damage, do not throw it away first till the complete device and its 
accessories succeed in the electrical and mechanical property tests.   

2.  Check the Accessories   

The supplied accessories are described in the 

Appendix A: Enclosure (page 22)

 of this 

Manual. You can check whether there is any loss of accessories with reference to 
this description. If it is found that there is any accessory lost or damaged, please get 
in touch with the distributor of NTL responsible for this service.   

3.  Check the Complete Instrument   

If it is found that there is damage to the appearance of the instrument, or the 
instrument does not work normally, or fails in the performance test, please get in 
touch with the NTL distributor responsible for your area. If there is damage to the 
instrument caused by the transportation, please keep the package. Immediately 
inform the supplier (NTL distributor). A repairing or replacement of the instrument 
will be arranged.   

 

 

Summary of Contents for P3245-1M





























Reviews: