background image

- 8 - 

6. 

Transportation and Installation 

 

 

 

 

 

(1) Transportation 

Be sure to transport the body while holding the base or the mount. If the chute or the return trough is held 

for transportation, the chute may be deformed or the trough position may deviate.   

 

 

 

 

 

 

 

 

     

†

  Note in transporting 

This machine is a heavy material. Watch out for dropping in transporting and be cautious enough. 

Especially, MD20 and MD30 must not be carried by single person. They must be carried carefully by 

more than one personnel or by use of lifting apparatus or hoisting attachment with sufficient lifting 

capacity. 

* Refer to item 11 Specification for the mass of the body (adding the mass of chute if attached). 

(2) Installation 

Fix the base firmly with the fixing bolts (fix cushion rubber screw part for the type without base) on the 

place (such as a bench) with sufficient strength. Little vibration will be felt when the base is touched in 

operation, if the machine is installed properly. 

†

  Caution for installation 

[1]  Be sure to wear safety gloves to prevent the sharp edges of the chute and others from touching 

bare hand. 

[2]  Do not operate the machine on a base with insufficient strength or in an unstable place. 

[3]  Do not allow the vibrating part of the machine (except the base) to be in contact with some other 

things in fixing. 

[4]  When the machine is inclined in installation, specified capability cannot be obtained. Be sure to 

level the machine. 

[5]  When perform welding work or grinding work nearby the feeder body, protect the feeder body all 

over with a protective cover. Incompliance may deteriorate the performance because iron powder 

etc. jumps into the machine. 

[6]

 

The structure is designed so that clearance is provided between chute mount and return trough. 

When such as oil and dust drops through the clearance, provide oil drain / dust exhaust (oil pan) 

system additionally for use.   

 

CAUTION 

The body is a heavy material. Transport the body 

carefully with care not to cause drop. 

Summary of Contents for K-MD10LB1



















Reviews: