50
V
oice/Videophone
Calls
Brightness
……
Five brightness levels (-2 to 0 to +2)
are available.
White balance
……
Sets image color tones.
→
p.123
This setting is also applied to the equivalent camera
functions.
Color mode set
……
Selects the image effect from
“Normal/Sepia/Monochrome”.
This setting is only retained during the call.
Photo mode
……
Sets modes suited to the scene
being shot.
→
p.122
Chara-den set.
……
Set the following when Chara-den is
used. This setting cannot be set for the camera images.
Switch Chara-den
……
Selects the character to be
displayed.
Action List
……
Checks the available actions and
the corresponding keys. You can also view the action
list by pressing
w
.
Change Action
……
Changes the Action mode.
Switch image
……
Displays the image selected in
“Substitute image” (p.67) on the other party’s display.
Display light
……
Sets lighting of backlight.
All time ON
(default)
……
Turns the backlight on all
the time.
15 seconds ON
……
Turns the backlight on for 15
seconds only.
Own number
……
Displays your phone number during a
videophone call.
Send DTMF tone
⇔
DTMF tone OFF
……
Sets/cancels
push signal transmission mode during Chara-den.
Except for Chara-den, videophone calls are always in
push signal transmission mode.
Change to voice
→
p.50
●
If a videophone call is not connected
When a videophone call is not connected, the cause
of the failure appears.
z
The cause may not appear depending on the
situation.
z
Depending on the type of other party’s phone or the
possible lack of a network service subscription, the
reason may not accurately reflect the other party’s
actual status.
z
If the videophone call is not connected, your call is
automatically switched to a voice call when you set
“Auto redial as voice” to “ON”. However, the call
may not be handled in this way if you call an ISDN
synchronous 64K, ISDN videophone which does
not support the 3G-324M standard (as of May,
2008) or if you dial a wrong number. Note that call
charge may be applied in some cases.
Switching a Voice/Videophone
Call During a Call (Caller)
z
You can use this function with the terminals
compatible with voice call/videophone call switch.
z
You can switch the voice call only when you are the
caller.
z
To switch the call, the receiver needs to set “Ntfy
switch-mode” to notify the switch beforehand.
→
p.67
<Example: To switch a voice call to a videophone call>
1
In-call screen (p.48)
d
(V.phone)
“YES”
While switching, the screen which indicates that
the calls are being switched appears and the
voice guidance is played.
Display
Cause
Check number then
redial
Phone number is not available
Busy
The line is busy
Busy with packet
transmission
The other party is using packet
communication
Out of service area/
power off
The other party is out of service
area or the phone is turned off
Your call is being
forwarded
The call is being forwarded (A
Videophone call is made when
the forwarding number is for a
3G-324M-compatible
videophone.)
Redial using voice
call
The phone for the forwarding
number is not compatible with
videophone calls.
Please activate caller
ID before dialing again
The other party sets the Caller
ID request service.
Your call cannot be
connected
The other party sets the
Nuisance call blocking service.
Upper limit has been
exceeded
Connection failed
The upper limit set for a Limit
billing plan (Type Limit and
Family Wide Limit) is exceeded.
Connection failed
Set Caller ID Notification to
“ON” and retry
You connected without notifying
your caller ID (when dialing into
visualnet, etc.)
• This message may also
appear in other situations.
Please make your
call from the i-mode
web page
You attempted to make a
videophone call to watch V-live
without browsing the i-mode
official site.
Display
Cause
