background image

5

31. 08. 21. Document Number  671746

Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk

BPS (V/T)-ES

Installation Manual

5.0 UNIT ACCESS

In this product range, several unique concepts have been 
implemented with a view to simplifying the installation design.

The unit must be installed with at least 600mm clearance from a 
wall/barrier. With this absolute minimum clearance, the unit may 
be connected to the power supply and control connection.

With this clearance, unit filters may be changed, and the fans 
coils, heat exchanger and condensate tray may be inspected and 
cleaned if necessary.

The LPHW and Electrical heater settings, coil bleed and drain, and 
all other control adjustments are similarly accessible.

Side access, where possible, is preferred in all cases in terms of safe 
working access to the equipment under the CDM regulations.

Note however, that access in the situation is difficult and 
additional time should be allocated. For convenience it is preferred 
that wherever possible, this minimum access provision is not 
adopted, and it is recommended that a minimum of around 
600mm clearance (as stated in ADF 2010) is allowed.

Where these arrangements are not suitable, the Consultant’s 
and Contractor’s project specific requirements will always be 
accommodated where possible.

5.1 Hinged / Removable Panel Access

All hinged access panels will be lockable and removable via locked 
hinges which can be opened for panel removal. All keys are identical 
and will open any handle or hinge.

The hinges do not need to be unlocked in normal operation of opening 
and closing.

 
 

Removable Hinged Access Panel (Hinged)

 
 

Removable Hinged Access Panel (Removed)

 
 

Easily removable  

blowers for maintenance

Access to built-in controls

Interchangeable filters 

slide in and out

Hinged or removable access panels

Access to Plate Heat Exchanger or 

Thermal Wheel

Access to interchangeable 

coils, LPHW heater and 

chilled water cooling 

option

8mm outside diameter 

condensate drain. 

Condensate pump fitted 

as standard (where 

necessary).

Unit Access

Summary of Contents for BPS T-ES

























Reviews: