background image

8

27. 11. 17. Leaflet Number 671721

Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and 

dimensions of equipment and the right is reserved to make such changes without prior notice.

10.0  Replacement  of Parts

Should any component need replacing Nuaire keep extensive

 

stocks

 

for  quick delivery. Ensure that  the unit  is  electrically  isolated, before

 

carrying  out  any  work.
Note: The supply  cable must  be replaced  by  an  electrically 
competent

 

person. 

When  ordering  spare parts, please quote the serial number  of  the

 

unit  and  the ARC  number of  the purchase if  possible.

(This information will  be available on the fan label).

11.0 Warranty

The 5 year warranty starts from the day of delivery and includes parts 
and labour for the first year and parts only for the remaining 4 years. 

This warranty is void if the equipment is modified without 
authorisation, is incorrectly applied, misused, disassembled, or not 
installed, commissioned and maintained in accordance with the 
details contained in this manual and general good practice. 

The product warranty applies to the UK mainland and in accordance 
with Clause 14 of our Conditions of Sale. Customers purchasing from 
outside of the UK should contact Nuaire International Sales office for 
further details.

12.0 After Sales Enquiries

For technical assistance or further product information, including 
spare parts and replacement components, please contact the After 
Sales Department.

Te

lephone

 02920

 

858

 

400

Installation and Maintenance

The WH1 Wall Mounted Range of Units

Summary of Contents for Ecosmart MRXBOX95-WH1-1Z









Reviews: