background image

1

Code description example

S* (T) (NC) -XB*-* *  2WP

| |

|

| | | |

|

1

2

3

45 6 7

8

1. 

1 = Unit size 2 to 10.

2. T = Optional Twin (run & standby) extract fan; available as

vertical stacked XBV for sizes S2 - 6T and S8T or horizontal

XBH for size S8T.

3.

Ecosmart control as standard. NC = optional no control version,

FC = optional fan speed control only.

4. V = Vertically stacked unit, H = side-by-side unit (available for

S6 to S10 only).

5. L = Left hand, R = right hand (see illustrations).

6. E = Electric heater (sizes 2 to 8 inclusive), L = LPHW coil,

N = No heater fitted.

7.

2 = 2 row heating coil.

8. WP = Optional weatherproof cover.

Example: S2-XBV-LE is size 2, vertically stacked with electric heater

and left hand access.

S6NC-XBH-RL is a size 6 with no controls, horizontal side-by-side

unit, right hand access and LPHW heating coil.

SQURBO XBOX

(Pre-packaged heat recovery unit)

Installation, Operating and

Maintenance Instructions

The EMC Directive 

20

1

4/

30

/E

U

  

The Low Voltage 

directive 

20

14

/

35

/E

U

Figure 2: S2/5-XBV-RN (right hand with no heater).

Figure 1: S2/5-XBV-LE (left hand with electric heater).

Nuaire Limited

Western Industrial Estate  Caerphilly  United Kingdom  CF83 1NA  

T: 029 2085 8400  F: 029 2085 8444  E: info@nuaire.co.uk  W: www.nuaire.co.uk

08. 06. 18. Leaflet Number 671408

Figure 5: S7/8-XBH-RE (right hand with electric heater).5

Intake

Exhaust

Extract

Supply

Figure 3: S6-XBH-RE (right hand with electric heater).

Intake

Exhaust

Extract

Supply

Figure 4: S6-XBV-LE (left hand with electric heater).

Supply

Extract

Exhaust

Intake

Figure 6: S7/8-XBV-RL (right hand with LPHW).

AHU with Heat Recovery section and direct drive AC motor technology.

AHU with Heat Recovery section and direct drive EC motor technology.

AHU with Heat Recovery section and direct drive AC motor/Inverter technology.

Supply

Extract

Exhaust

Intake

Exhaust

Intake

Supply

Extract

Exhaust

Intake

Supply

Extract

Summary of Contents for ecosmart SQURBO XBOX

















Reviews: