5
26. 05. 20. Document Number 671944
Nuaire |
Western Industrial Estate
|
Caerphilly
|
CF83 1NA
|
nuaire.co.uk
MEV-ECO(-H)
Installation Manual
5.0 COMMISSIONING
Due to potential access to live parts adjustment of set points must
only be carried out by a suitably qualified person, adjustment
should only be carried out using an VDE approved insulated
terminal screwdriver.
The clear panel covering the ventilation controls has an adhesive
backing which should be exposed and sealed post commissioning to
prevent tampering and ensure the IPX4 rating is met.
All commissioning set points can be accessed through the access holes
of the control cover (Figure 1).
For required airflow rates please refer to the design specification for the
property or building regulations approved document F.
Correct commissioning is essential to ensure the ventilation rates
are met. It also ensures the unit is not over ventilating and causing
excessive power consumption.
Adjustment valves should be locked in place to prevent further
adjustment.
Once commissioned the home owner/tenant should be informed that
the unit should not be adjusted as it will have a detrimental effect
on the indoor air quality and could result in condensation and mould
growth.
5.1 Humidity Adjustment (MEV-ECO-H Only)
The MEV-ECO-H contains an internal humidity sensor, when the unit
senses that the humidity exceeds the set point the unit will boost to
that set by the commissioned boost speed. The set point can be found
on the control cover of the unit (Figure 1) and is at its least sensitive
when turned fully clockwise, the mid-point is approximately 75% RH.
The sensor is measuring humidity from all the wet rooms at the same
time and should not be relied on to solely boost the unit. An additional
switch should be used local to the wet rooms ("Wiring diagrams" on
page 4).
7
MEV-ECO-H Ventilation Controls
6.0 MAINTENANCE
IMPORTANT
Isolation - Before commencing work make sure that the unit
and switched live control are electrically isolated from the
mains supply and switched live supply.
It is important that maintenance checks are recorded and that the
schedule is always adhered to, in all cases, the previous report should
be referred to.
7.0 WARRANTY
The 5
year warranty starts from the day of delivery and includes parts
and labour for the first year. The remaining period covers replacement
parts only.
This warranty is void if the equipment is modified without
authorisation, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the details
contained in this manual and general good practice.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Conditions of Sale. Customers purchasing from
outside of the UK should contact Nuaire International Sales office for
further details.
Failure to maintain the unit as recommended will invalidate the
warranty.
8.0 END-OF-LIFE AND RECYCLING
Where possible Nuaire use components which can be largely recycled
when the product reaches its end-of-life:
•
Fans, motors, controls, actuators, cabling and other electrical
components can be segregated into WEEE recycling streams.
•
Sheet metal parts, aluminium extrusion, heating/cooling coils and
other metallic items can be segregated and fully recycled.
•
EPP, plastic ducting, nylon corner pieces, plastic heat exchangers,
packaging material and other plastic components can be
segregated into mixed plastic and widely recycled.
•
Cardboard packaging, wood, used filters and other paper
components can be largely recycled or fully processed in energy
from waste centres.
•
Remaining Items can be further segregated and processed in
accordance with the zero waste hierarchy. Please call After Sales
Support for further information on items not listed above.
IMPORTANT
Ensure that Nuaire product is made safe from any electrical
supply before dismantling commences. This work should only
be undertaken by a qualified person in accordance with local
authority regulations and guidelines, taking into account all
site based risks.
9.0 AFTER SALES AND REPLACEMENT PARTS
For technical assistance or further product information, including spare
parts and replacement components, please contact the After Sales
Department.
If ordering spares please quote the serial number of the unit together
with the part number, if the part number is not known please give a full
description of the part required. The serial number will be found on the
identification plate attached to the unit casing.
Telephone 02920 858 400
aftersales@nuaire.co.uk
