background image

 

 
 

 
 
 

 
 

 
 

 
 

 
 

 
 

 

CONTENTS

Safety Precautions

 

Setup & Installation

Controls

 

Cable Setup

Platter Setup

 

Interchanging Tonearm Tubes

 

Tone Arm Setup

 

Cartridge Setup

 

Important Notes & Operation

Specifications

Trouble Shooting

1

 

3

 

4

 

7

 

8

 

9

 

10

 

11

 

12

 

13

 

14

 

OPERATING INSTRUCTIONS

IMPORTANT

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of un-insulated "dangerous voltage"

within the product's enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

 

NOTICE

 

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

CAUTION!

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

 

NOTICE

 

The apparatus shall not be exposed to dripping or splashing and that no objects

filled with liquids, such as vases, shall be placed on the apparatus.

Summary of Contents for TT500

















Reviews: