24
PROBLEM
CAUSE
SOLUTION
Machine will not operate
Missing or blown fuses
Key in the ‘OFF’ position
Low battery charge
Machine stop button in ‘OFF’ mode
Machine is connected and charging
Fit or replace fuse (page 7)
Turn key to ‘ON’ position (page 7)
Charge batteries (page 19)
Reset stop button (page 12)
Take off charge (page 19)
Vacuum will not operate
Floor tool in raised position
Waste water tank full
Lower floor-tool (page 8)
Empty waste water tank (page 15)
Poor water pick-up
Waste-water tank full
Clogged / blocked vacuum hose
Loose hose connections
Debris basket filter clogged / blocked
Separator air filter clogged / blocked
Poor separator seal
Damaged separator seal
Damaged / split vacuum hose
Damaged floor-tool blades
Low battery charge
Empty waste-water tank (page 15)
Remove and clean (page 15)
Push tight connections (page 14)
Remove and clean (page 16)
Remove and clean (Page 15)
Clean and refit (page 15)
Renew (contact service dept)
Renew (contact service dept)
Renew (contact service dept)
Recharge batteries (page 19)
No brush / scrub function
No brushes fitted
Brush deck raised
Check and fit (page 9)
Lower brush deck (page 9)
Little or no water flow
Clean-water tank empty
Clean-water tank filter blocked/ clogged
Incorrect water flow setting
Brush deck raised
Fill clean-water tank (page 10)
Remove and clean (16)
Adjust as desired (Page 11)
Lower brush deck (page 9)
Machine just ‘stops’ while
operating
Too much load on the brush system
Reset the machine using the key and
decrease the brush load to best suit the
floor type (page 12)
Trouble Shooting
Model - CRO 8055
(Empty) Net Weight
120 A/Hr
Brush
Weight
Brush
Width
Brush
Pressure
Pad
Width
Pad
Pressure
Brush Motor
Vac
motor
200 kg
23 kg
550 mm
11.4 G/cm
2
508 mm
9.3 G/cm
2
24V
600 W
24 V
400 W
Transaxle
Run Time
2 x 120 A/Hr
Run Time
2 x 100 A/Hr
Total Battery
Weight
120 A/Hrs
Total Battery
Weight
100 A/Hrs
Charge Times
2 x 120 A/Hrs
Charge Times
2 x 100 A/Hrs
24 V
400 W
3 hrs
2 hrs
74 kg
(163 lbs)
62 kg
(136 lbs)
10A = 12 hrs
20A = 7 hrs
35A = 4.5 hrs
10A = 8 hrs
20A = 5-6 hrs
35A = 3-4 hrs
Brush
Speed
AirFlow
Transit
Speed
Capacity
Water Flow
Rates
Cleaning
Area
Sound Pressure
Hand Arm
Vibration
150 rpm 24.2 L/sec 0-6 km/hr
80 L /
80 L
0.5 / 1.0 / 1.5
2.0 / 3.0
L/min
1700 m
2
@ 3.5 K/Hr
≤
70dB (A)
Travelling (Quarry Tiles)
1.84 m/s
2
(Uncertainty 0.92 m/s
2
)
ISO 5439-1
Whole Body Vibration
Height
Length
Width
Travelling (Quarry Tiles)
1.11 m/s
2
(Uncertainty 0.56 m/s
2
)
ISO 2431-1
1160 mm
1460 mm
805 mm
Specifications
Summary of Contents for CRO 8055/100T
Page 27: ...27...
