background image

20

T 01460 68600

Information for Scrubber Dryer

As with all electrical equipment care and attention must be exercised at all times during its use, in addition to ensuring that routine and 

preventative maintenance is carried out periodically in order to ensure its safe operation.

 

Failure to carry out maintenance as necessary, including the replacement of parts to the correct standard 

could render this equipment unsafe and the manufacturer can accept no responsibility or liability in this respect.

When ordering spare parts always quote the Model Number / Serial Number specified on the Rating Plate.

Warning do not use on slopes exceeding 2%.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning 

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance. 

When detergents or other liquids are used, read the manufacturer’s instructions.

Only use brushes provided with the appliance or those specified in the instruction manual. 

The use of other brushes may impair safety. 

A full range of brushes and accessories are available for this product. 

Only use brushes or pads which are suitable for the correct operation of the machine for the specific task being performed.

It is essential that this equipment is correctly assembled and operated in accordance with current safety regulations.

When using the equipment always ensure that all necessary precautions are taken to guarantee the safety of the operator and

any other persons who may be affected. 

Wear nonslip footwear when scrubbing. Use a respiratory mask in dusty environments.

The machine, while charging, must be positioned so that the mains plug is easily accessible.

When cleaning, servicing or maintaining the machine, replacing parts or converting to another function the power source shall be switched off.

Mains operated machines shall be disconnected by removing the power plug, and battery operated machines shall be disconnected by removing the fuse.

In order to prevent unauthorised use of the machine the power key must be removed after use.

Machines left unattended shall be secured against unintentional movement.

When detergents or other liquids are used, read the manufacturer’s instructions.

Operators shall be adequately instructed as to the correct use of the machine.

If this product does not have a factory installed Numatic battery charger, then it is the responsibility of the owner and user of the product to ensure that the 

charging system and battery combination are compatible, fit for purpose and safe to use.

This machine is not suitable for picking-up hazardous dust.

Do not use on surfaces having a gradient exceeding that marked on the appliance.

This machine shall be stored indoors only

This machine is for indoor use only.

Read the instruction manual before using the appliance.

This product meets the requirements of IEC 60335-2-72

NOTES: This machine is also suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and 

offices for other than normal housekeeping purposes.

•  Ensure only competent persons unpack/assemble the machine.

•  Keep your machine clean.

•  Keep your brushes in good condition.

•  Replace any worn or damaged parts immediately.

•  Regularly examine the power cord for damage, such as cracking or ageing. If damage is found,

  replace the cord before further use.

•  Only replace the power cord with the correct Numatic approved replacement parts.

•  Ensure that the work area is clear of obstructions and / or people.

•  Ensure that the working area is well illuminated.

•  Pre-sweep the area to be cleaned. 

•  Use steam cleaners or pressure washers to clean the machine or use in the rain.

•  Attempt machine maintenance or cleaning unless the power plug has been removed from the supply outlet.

•  Allow any inexperienced repairs. Call the experts.

•  Strain cable or try to unplug by pulling on cable.

•  Leave the brush pad on the machine when not in use.

•  Allow the machine to be used by inexperienced or unauthorised operators or without appropriate training.

•  Use the machine without the solution tanks properly positioned on the machine, as shown in the instructions.

•  Expect the machine to provide trouble-free, reliable operation unless maintained correctly.

•  Run the machine over power cable during operation.

•  Lift or pull the machine by any of the operating triggers, use the main handle.

•  Remove the handle from the machine except for service and repair.

WARNING

CAUTION

DO

DON’T

ORIGINAL INSTRUCTIONS

READ MANUAL BEFORE USE

COMPONENT

INTERVAL

INSPECT FOR

Mains Lead

DAILY

Scuffing, cracks, splits, conductors showing

Brushes

DAILY

Bristle damage, wear, drive collar wear

Squeegee Blade

BEFORE EACH USE

Wear, cracks, splits

Filters

BEFORE EACH USE

Clogging and debris retention

Tanks 

AFTER EACH USE

Rinse dirty water tank after use

Summary of Contents for TGB 6055/100





























Reviews: