background image

Operating Instruction and Documentation 

                                                                                       SPL 4000  

 

- 5 - 

 

 Filling out and undersigned and copying this sheet and send the original to the lift 
manufacturer. The copy remains in the manual.
 

 

Otto Nußbaum GmbH & Co. KG 

Korker Straße 24 

D-77694 Kehl-Bodersweier

 

 

Record of installation

 

 

The automotive lift with the 

 

serial number:............................................  was installed on:............................................... 

 

at the firm:................................................. at:..................................................................... 

 

The initial safety check was carried out and the lift was started. 

The installation was carried out by the operating authority/competent (please delete as applicable). 

The initial safety check was carried out by a competent person before the initial operation. 

The operating authority confirms the correct installation of the automotive lift, the competent person 

confirms the correct initial operation. 

 

Used Dowels(*):________________________________(Type/Name)      
 
Minimum anchorage depth (*) kept: _________________mm   

 

 

F

 ok 

 
Starting torque (*) kept: __________________________NM  

 

 

 

F

 ok 

 

............................................ .....................................................  ............................................ 

date        name 

of 

the 

operating 

authority  

signature of the operating authority 

 

............................................ .....................................................  ............................................ 

date        name 

of 

the 

competent 

person   

signature of the competent person 

 

 

Your customer service:.....................................................................................................(stamp) 

(*) see supplement of the dowel manufacturers  

Automotive Lift date: 07/2005 / Manual date: 04.12.2007

Summary of Contents for SPL 4000







































Reviews: