background image

TO REGISTER THIS PRODUCT, VISIT WWW.NUTONE.COM

INSTALLATION INSTRUCTIONS

READ & SAVE THESE INSTRUCTIONS!

Two-Note Door Chime

• For use with either a transformer or batteries

LOCATION

TRANSFORMER:

Mount a 16-volt transformer to a conveniently located junction box.

Attic location is not recommended. 

PUSHBUTTON:

The chime is designed for two-note operation. Select pushbutton

locations at front and rear (or side) doors. Do not use lighted pushbuttons with
battery-operated chime.

NEW INSTALLATION

INSTALLING TRANSFORMER

Disconnect house power until installation is complete. All wiring must comply

with local codes.

1. Use a 16 VOLT, 10 VA transformer.
2. 

Refer to Figure 1.

Mount transformer to a conveniently located junction box. Do not

mount transformer in attic.

3. Use approved wire connectors to connect supply wires to transformer leads: white to

white; black to black.

FIGURE 1

FIGURE 2

FIGURE 3

SUPPLY WIRE

REPLACEMENT OR NEW INSTALLATION USING TRANSFORMER

NEW INSTALLATION USING BATTERIES

FRONT DOOR

PUSHBUTTON

FRONT DOOR PUSHBUTTON

REAR DOOR PUSHBUTTON

120vAC

TRANSFORMER 16
VOLT, 10VA 

FOR ONE DOOR OR
TWO DOORS

CHIME BASE

TERMINAL BOARD

TO 120
HOUSE
WIRING

R

DO NOT OIL
C - BAT. COMMON
T - TRANSFORMER
F - FRONT DOOR PB
R - REAR DOOR PB

REAR DOOR

PUSHBUTTON

FOR ONE DOOR

OR TWO DOORS

CHIME BASE
TERMINAL BOARD

“D

S

IZ

E

B

A

T

T

E

R

Y

“D

S

IZ

E

B

A

T

T

E

R

Y

WIRES TO
CHIME

CHIME
BASE

MAKE SURE
KEYHOLE
MOUNTING HOLE IS
AT THE TOP

PUSHBUTTON
AND
TRANSFORMER
WIRING

FIGURE 4

INSTALLING THE WIRING

1. Use standard bell/chime wire (20 gauge, two-conductor).

2. Run wires as shown in Figure 2 for installation using transformer.

3. Run wires as shown in Figure 3 for installation using batteries.

MOUNTING CHIME BASE

Refer to Figure 4.

1. At chime location, cut a 1" diameter hole (for pushbutton and transformer wiring) in

the wall.

2. Pull wiring through two holes in chime base.

3. Use two provided screws to mount chime base to wall. 

Make sure keyhole

mounting hole is at top.

C

F

T

“D

S

IZ

E

B

A

T

T

E

R

Y

“D

S

IZ

E

B

A

T

T

E

R

Y

R

DO NOT OIL
C - BAT. COMMON
T - TRANSFORMER
F - FRONT DOOR PB
R - REAR DOOR PB

C

F

T

WIRING CONNECTIONS

1. Use wire nuts to make connections. Insulate all connections with electrical tape.

2. 

INSTALLATION USING TRANSFORMER.
Refer to Figure 2.

Connect pushbutton and transformer wires to terminal screws

marked Front, Transformer, and Rear.

3. 

INSTALLATION USING BATTERIES.
Refer to Figure 3. 

Connect pushbutton wires to terminal screws marked Front,

Common, and Rear.

WIRING HINTS

1. Carefully fasten wiring to wall studs and ceiling

joists. Avoid short circuits caused by staples or
clops cutting through the wiring's insulation.

2. Loop wire around terminal screws.

3. When connecting more than one wire to a

single terminal screws, twist the wires together before looping them around the
terminal screw.

4. Make sure all terminal screws are tightened securely.

BATTERY INSTALLATION

1. Install four (4) “D” size batteries as shown in Figure 4.

2. For longer life, alkaline batteries are recommended.

REPLACEMENT INSTALLATION

1. Turn off house power until installation is complete.

2. Remove cover from existing chime and disconnect wires from terminal screws. Label

all wires (Front, Transformer, Rear) as you remove them. 

NOTE:

Any additional wires

(for example: common or side) should be individually capped with wire nuts or sealed

with electrical tape and pushed back into the wall cavity. These wires are not needed.

3. Remove existing chime base from wall.

4. Pull wires through holes in new chime base.

5. Use provided screws to mount base to wall.

6. Connect wires to terminal screws marked Front, Transformer, and Rear on the chime

base.

7. Place chime cover securely over the base.

8. Restore house power to chime.

Use Only Unlighted Pushbuttons

 

Reviews: