1
NPD300Z
Z-Wave Radio Frequency (RF) Controlled
Plug-In Lamp Module
300 Watts, 120 VAC, Series 300
NOTE:
This module must be “included in the Network”
only where it will be permanently installed.
You cannot “test bench: configure this
module, then install. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes.
NPD300Z PLUG-IN LAMP MODULE
NuTone’s family of Z-Wave
®
certified wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent wireless
capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. Embedded in each device,
the Z-Wave smart chip enables two-way RF communication among hundreds
of Z-Wave enabled devices, allowing products and services from multiple
manufacturers to work seamlessly.
NuTone Z-Wave products are easy to install, and allow dealers to create an
integrated wireless network with nearly limitless expansion and interoperability
with security and health monitoring systems, energy management, home
entertainment, appliances, and more.
This product supports 40Kbps data transmission.
This product can also be
used for networking support in systems that stream metadata. An example might
include transmission of information from audio devices such as song title, artist,
and album information to various displays around the home. As part of a Z-Wave
network, the NPD300Z can act as a wireless repeater to insure that commands
intended for another device in the network are received. This is useful when the
device would otherwise be out of the radio range of the wireless controller.
INSTALLATION
Plug this Lamp Module into the wall outlet near the lamp to be controlled, and
plug the lamp into the Lamp Module. Make sure the lamp(s) to be controlled
total no more than 300 watts.
To reduce the risk of electric shock, this product has a grounded type plug that
has a third (grounding) pin. This plug will only fit into a grounding type power
outlet. If the plug does not fit into the outlet, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
WARNING:
Plugging a non-resistive load such as florescent lighting or a device
with a motor may result in damage to the Lamp Module and will void the warranty.
INCLUDING NPD300Z TO THE NETWORK
1.
Prepare the Controller to include a unit to the network, by adding it to a group
(method of adding a node to the network). Refer to controller instructions.
2. The NPD300Z must be in its permanently installed location.
Tap the
button on the NPD300Z once.
3.
You should see an indication on your Controller that the “DEVICE WAS
INCLUDED” in the network.
✓
NOTE:
If you have trouble adding the NPD300Z to a group it may be that the
Home ID and Node ID were not cleared from it after testing. You must first “RESET
UNIT” with your controller to remove it from the network. Although adding it to a
group includes it in the network, removing it from a group does not remove it from
the network. If removed from a group, it functions only as a repeater.
INTEROPERABILITY WITH Z-WAVE™ DEVICES
A Z-Wave network can integrate devices of various classes of products, and
these devices can be made by different manufacturers. The NPD300Z has
Z-Wave certification which guarantees interoperability.
BASIC OPERATION
Button (Local Control)
The button on the NPD300Z allows the user to:
• Turn ON, OFF, or DIM and BRIGHTEN the load attached to the controlled outlet.
• Tapping button toggles the load attached.
• Pressing and holding the button will dim or brighten the load attached.
Operation Note
When a light bulb reaches the end of it’s life and burns out, it sometimes
creates a momentary short circuit. The high current that results may cause the
dimmer to respond by turning off. Should this happen, replace the bulb with a
new one. The dimmer can now be operated to restore power to the light.
Remote Control
The NPD300Z will respond to Basic, Multilevel and Scene Activation commands
that are part of the Z-Wave system. Refer to your controller’s instructions as to
whether your controller can transmit those commands.
ADVANCED OPERATION
Protection
The NPD300Z supports the Protection Command. The NPD300Z can be set
to any one of three
Protection
modes by a wireless controller. Refer to your
controller for information on how to set the various modes of
Protection.
Some
controllers may only be able to set certain settings of Protection:
There are three modes of
Protection
and they are the following:
• No protection
• Child protection
• Local Button totally disabled
No Protection
When
Protection
is set to “
No Protection
” mode,the NPD300Z works normally,
unit will turn on and off with the button on the unit, or with the wireless controller.
Child Protection
When
Protection
is set to “
Child Protection
” mode, you are required to press
the button on the unit 3 times rapidly to control the attached load. The NPD300Z
continues to operate normally using a wireless controller.
Button Totally Disabled
When Protection is set to “Button totally disabled” mode the button will not work
to turn the unit on or off. The button can still be used, however, to access the
Z-Wave network. The NPD300Z continues to operate normally using a wireless
controller.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,NPD300Z; P/N: 10005982 X2 INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOL ± .125”; SCALE: 1-1; PAGE 1 OF 2
Button Functions
1.
Use to include module under the command
of a Controller.
2.
Local ON and OFF (push and release).
3.
Local dimming (hold down).
