13
GB
function.
Check correct alignment of moving parts, making sure they do
not bind. Check for any damaged components and make sure
that the power tool has been correctly assembled.
Check for any condition that may affect operation of the power
tool.
Unless otherwise indicated in this instructions handbook, a
guard or any other part of the power tool that has been damaged
must be repaired or replaced by an authorized service center.
Any switch that does not work correctly must be replaced by an
authorized service center.
Do not use the power tool if the ON/OFF switch does not turn
the power tool ON and OFF.
Dust generated when machining materials is a health hazard.
Always wear a suitable dust mask.
When working, always wear personal protective equipment:
safety goggles, gloves, mask, ear protectors, non-slip safety
shoes.
Never wear loose clothes or jewelry that may be trapped in
moving parts; long hair must be tied back.
Always work on a stable base.
Always fasten the workpiece securely with a clamp.
Keep the work area clean and tidy.
Always use the power tool with both hands.
Never open or modify the power tool or its accessories in
any way.
Do not expose the power tool to rain, or use in damp or wet
locations. Keep the work area well lit.
Do not use power tools in areas where there is a risk of explosion
or fire from combustible materials, flammable liquids, paint,
varnish, petrol etc. flammable gases and dust of an explosive
nature.
Beware children and pets
Children and pets should be kept out of the work area.
All power tools should be kept out of the reach of children and,
preferably, stored or locked in a secure cabinet or dry room
when not in use.
Use the right tool
Select the right tool for the job. Do not use a tool for a job for
which it was not designed. Do not force a small tool to do the
job of a heavy-duty tool. Do not use tools for purposes not
intended.
Do not force the power tool
The power tool will do a better and safer job and give you much
better service if it is used at the rate for which it was designed.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance.
Follow the instructions for lubricating and changing accessories.
Keep handles dry, clean and free from oil and grease.
Ensure that ventilation slots are kept clean and free from dust
at all times. Blocked ventilation slots can cause overheating and
damage to the motor.
If this machine is to be used when working at a certain height,
scaffolding fitted with railing and kick-plate or a tower platform
must be used in order to guarantee suitable stability.
GUARD AGAINST ELECTRIC SHOCK
Avoid body contact with earthed or grounded surfaces (e.g.
pipes, radiators, dish-washers and refrigerators).
Power Cords
Never yank or pull the power cord to disconnect it from the
mains supply socket.
Never carry the power tool by its power cord. Keep the power
cord away from heat, oil, solvents and sharp edges.
Check the tool power cord periodically and if damaged have it
replaced by an authorized service center.
Inspect extension cords periodically and replace if damaged.
DO NOT use 2-core extension cords or reels on power tools
with an earth path. Always use a 3-core extension cord or reel
with the earth core connected to earth.
Always unwind any extension cords fully.
For extension cords up to 15 metres, use a wire cross section
of 1.5mm
2
.
For extension cords over 15 metres, use a wire cross section
of 2.5mm
2
.
Protect your extension cord from sharp objects, excessive heat
and damp or wet locations.
This power tool complies with National and International
Standards and safety requirements. Repairs should be
carried only out by qualified persons using original spare
parts. Failure to do so may result in considerable danger
to the use.
Summary of Contents for NCD12
