background image

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

12

11

9

10

9. Attach the three side panels to the heater

using 18pcs screw 3/16”. 

Note : Do not cover the front side where

the control knob is.

KK

LL

H

MM

DD

Hardware Used

DD

JJ

x 18

Philips 

screwdriver

3/16” Screw

x 1

10

.

Install the knob to M4x6 screw. Hang the

chain to the hole on the control box assy and 

put the pothook of front panel to the holes of 

bottom plate.

Hardware Used

x 1

KK

Knob

LL

JJ

x 1

x 1

Philips 

screwdriver

Screw M4

x6

x 1

MM

Chain

11

11. Screw gas hose and regulator to propane cylinder

(not included). Do not cross-thread.

Every part of the heater shall be secure against 

displacement and shall be constructed to maintain a 

fixed relationship between essential parts under normal 

and reasonable conditions of handling and usage. Parts 

not permanently secured shall be designed so they 

cannot be incorrectly assembled and cannot be 

improperly located or misaligned in removing or 

replacing during cleaning or other servicing.

Use a standard 20 lb. propane cylinder only.  

(approximately 12.2 in. / 31cm. in diameter and 17.9 in.

/ 45.5cm high).

Use this heater only with a propane vapor

withdrawal supply system. See chapter 5 of the standard

for storage and handling of liquefied petroleum gas,

ANS/NFPA 58. Your local library or fire department

should have this book. Storage of an appliance indoors 

is permissible only if the cylinder is disconnected and

removed from the appliance. A cylinder must be stored

outdoors in a well-ventilated area out of the reach of

children. A disconnected cylinder must have dust caps

tightly installed and must not be stored in a building,

garage or any other enclosed area. The maximum inlet

gas supply pressure: 250 psi /1750 kPa. The minimum

inlet gas supply pressure: 25 psi /175 kPa. Manifold

pressure with regulator provided: 11 inch W.C/ 2.74 kPa.

The pressure regulator and hose assembly supplied 

with the appliance must be used. The installation must 

conform with local codes, or in the absence of local 

codes,with national fuel gas code, ANS Z223.1/NFPA54, 

natural gas and propane Installation Code, CSA B149.1, 

or propane storage and handling code, B149.2.

I

Summary of Contents for AH001













Reviews: