background image

Voyager IV

 

Nitrox System 

Nuvair                                                                                                                                                                                                        www.nuvair.com 

Page 

27  

 

Always use Oxygen Analyzers to monitor oxygen content of any gas flowing through the 
System.  Both air and Nitrox are subject to variations in oxygen content. 
 

15.5 Shutting Down 

 

1)  When  the Storage Banks are finished filling  and tank valves are closed, the Nitrox System will 

automatically shut down at the pressure set on the pressure switch (3600 psi). 

2)  Manually shut off the Membrane System by turning the Feed Air Regulator adjustment knob CCW 

to reduce pressure to minimum setting and then turn off the LP & HP compressors. 

3)  The system will automatically drain all Filter, Compressor, and Volume Tank condensate. 

 

16.0    Nitrox Operation Notes 
 

16.1  Correlation of Feed air Pressure to Oxygen Content 

 

After the 10 hour break-in period for your Nitrox  System, you will notice that specific Nitrox  %O

2

’s 

always match specific feed air pressures once the System has warmed up.  These pressures will be 
repeatable.  If you find that the Fill Oxygen Analyzer reads 36% O

2

 when the feed air pressure is at 

125  psi  (9 bar), record this pressure or make a mark on the feed air  pressure gauge indicating the 
%O

2

.  Do this for each %O

2

 that you normally make, making sure System has warmed up first.  The 

next time Nitrox  with 36% O

2

  is needed, adjust the regulator to 125  psi  (9 bar) and wait for  the 

Oxygen Analyzer reading to stabilize. You will find the analyzer reading to be very close to 36% O

2

requiring only minor adjustments of the regulator to achieve the exact desired %O

2

 

 

Use the Fill Oxygen Analyzer to verify the Nitrox oxygen percentage prior to pumping.  When 
using the feed air pressure reading to obtain specific oxygen percentage, minor adjustments 
of the feed air pressure regulator may be required to obtain the exact percentage desired. 

 

16.2  Hot Fills 

 

While in the process of filling HP Nitrox  Storage Tanks, you may have a need to supply a walk-in 
customer with a Scuba Cylinder fill of a different Nitrox mix. You can change mixes as follows: 
 
1)  With the Nitrox System operating, isolate the HP Nitrox Storage Tanks from the HP Compressor 

by closing the appropriate valves. 

2)  Record the Membrane System feed air pressure reading. 
3)  Slightly open fill whip valve on the HP Compressor, and adjust so the running Compressor 

maintains 1500-2000 psi (100-140 bar) outlet pressure. 

4)  Adjust the B.P. feed air regulator to the pressure corresponding to the desired Nitrox %O

2

 for the 

Scuba Cylinder fill. 

5)  Allow the Fill Oxygen Analyzer reading to stabilize, make any minor adjustments necessary to 

achieve the desired %O

2

, and then fill cylinder in normal manner. 

6)  When finished return regulator to previous setting, and allow the Fill Oxygen Analyzer reading to 

stabilize.  Make any minor adjustments necessary to achieve the desired %O

2

, and then resume 

filling Storage Tanks. 

Summary of Contents for Voyager IV









































Reviews: