background image

NuPower Xtender™ VU4GX01 User Manual 

 

 

 

Rev 1.1 

 

4

 

HARDWARE INTERFACE  

 

The transceiver interface connector, “XCVR,” is SMA (female). 

 

The antenna connector, “ANT,” is SMA (female). 

 

The pin-out definitions for the 15 pin Micro-D socket connector, “CTRL/PWR,” are provided in 

Table 4. In a typical installation, the amplifier module is mated to a host controller board via a 

cable harness. 

 

 

The ANT SMA connector is the antenna connection. This connection should always 

be loaded into 50 

Ω

, otherwise the amplifier could be damaged. 

 

4.1

 

INTERFACE CONNECTOR    

The NuPower Xtender VU4GX01 features a 15 pin Micro-D interface connector for control, power, and 

ground connections.  

Table 4: NuPower Xtender Interface Pin-Out Definitions 

Socket No. 

Name 

I/0 

Description 

3, 4, 5, 6, 12, 13 

V Supply 

Primary Power (+28 VDC) 

1, 7, 8, 10, 11, 14, 15 

GND 

Signal and Power Ground 

Temp 

Over Temperature Flag 

TR_EN 

Transmit / Receive Enable 

 
The standard interface cable harness is comprised of 15 wires, includes a Micro-D connector with pins, 

and mates directly to the NuPower Xtender interface connector. 

4.2

 

DC POWER 

The nominal supply voltage for the NuPower Xtender VU4GX01 is +28 VDC.  

4.3

 

GROUND 

The signal and power grounds are tied together in the amplifier module. 
 

 

Summary of Contents for NUPOWER XTENDER VU4GX01












Reviews: